HP 200 HP StorageWorks 200 Storage Virtualization System site preparation guid - Page 20

General computer room requirements, Preventing electrostatic discharge - printer

Get HP 200 PDF manuals and user guides View all HP 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

General computer room requirements The goal of a computer room is to maintain an ideal environment for computer equipment, including this system. Make sure your computer room adheres to all national and local building codes for a data center/computer room environment. HP recommends that you follow these general guidelines: • Locate the computer room away from exterior walls of the building to avoid the heat gain from windows and exterior wall surfaces. • When exterior windows are unavoidable, use windows that are double or tripled glazed and shaded to prevent direct sunlight from entering the computer room. • Maintain the computer room at a positive pressure relative to the surrounding spaces to reduce introduction of contaminants. • Install a vapor barrier around the entire computer room envelope (floors/walls/ceiling) to help keep moisture out of the room. This is especially important if your computer room is located underground. • Caulk and vapor-seal all pipes and cables that penetrate the computer room envelope. Preventing electrostatic discharge Electrostatic discharge (ESD) can cause component damage, especially during servicing operations. Static charges occur when objects are separated or rubbed together. The voltage level of a static charge is determined by the following factors: • Types of materials • Relative humidity - low humidity tends to increase ESD voltage. • Rate of change - a standard air conditioner cools the air and lowers humidity. The faster the air is cooled and dried, the greater the likelihood of ESD. • Separation - refers to the static discharge that can be generated when two objects are separated. For example, printer paper is often stored in cool dry conditions. If opened and used immediately, the act of removing the paper from its box generates static. Follow these precautions to minimize possible ESD-induced failures in your computer room: • Install conductive flooring (conductive adhesive must be used when laying tiles). • Use conductive wax if waxed floors are installed. • Ensure that all equipment and flooring are properly grounded and are at the same ground potential. • Use conductive tables and chairs. • Store spare electric parts in antistatic containers. • Use proper cooling equipment to reduce the risk of ESD by maintaining recommended humidity level and airflow rates. • Leave boxes of paper open in the computer room for several hours before use to allow static to discharge gradually over time. 20 Site requirements

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
General computer room requirements
The goal of a computer room is to maintain an ideal environment for computer equipment, including
this system.
Make sure your computer room adheres to all national and local building codes for a data
center/computer room environment.
HP recommends that you follow these general guidelines:
•
Locate the computer room away from exterior walls of the building to avoid the heat gain from
windows and exterior wall surfaces.
•
When exterior windows are unavoidable, use windows that are double or tripled glazed and
shaded to prevent direct sunlight from entering the computer room.
•
Maintain the computer room at a positive pressure relative to the surrounding spaces to reduce
introduction of contaminants.
•
Install a vapor barrier around the entire computer room envelope (
fl
oors/walls/ceiling) to help
keep moisture out of the room. This is especially important if your computer room is located
underground.
•
Caulk and vapor-seal all pipes and cables that penetrate the computer room envelope.
Preventing electrostatic discharge
Electrostatic discharge (ESD) can cause component damage, especially during servicing operations.
Static charges occur when objects are separated or rubbed together. The voltage level of a static charge
is determined by the following factors:
•
Types of materials
•
Relative humidity — low humidity tends to increase ESD voltage.
•
Rate of change — a standard air conditioner cools the air and lowers humidity. The faster the air
is cooled and dried, the greater the likelihood of ESD.
•
Separation — refers to the static discharge that can be generated when two objects are
separated. For example, printer paper is often stored in cool dry conditions. If opened and used
immediately, the act of removing the paper from its box generates static.
Follow these precautions to minimize possible ESD-induced failures in your computer room:
•
Install conductive
fl
ooring (conductive adhesive must be used when laying tiles).
•
Use conductive wax if waxed
fl
oors are installed.
•
Ensure that all equipment and
fl
ooring are properly grounded and are at the same ground
potential.
•
Use conductive tables and chairs.
•
Store spare electric parts in antistatic containers.
•
Use proper cooling equipment to reduce the risk of ESD by maintaining recommended humidity
level and air
fl
ow rates.
•
Leave boxes of paper open in the computer room for several hours before use to allow static
to discharge gradually over time.
20
Site requirements