HP 200 HP StorageWorks 200 Storage Virtualization System site preparation guid - Page 26

If your c value is in between two table values, use the larger table value. Then, nd the row

Get HP 200 PDF manuals and user guides View all HP 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Calculate rack clearance dimensions as follows: • Clearance "a" is the space between the service clearance at the left side of the system (100 mm minimum for installing the kickplate) and any other object, such as a desk or wall. • Clearance "b" is the space between the service clearance at the right side of the system (100 mm for the kickplate) and any other object. • Clearance "c" is the space between the service clearance at the front of the system and any other object. • Use the value of "c" and your floor load rating to determine the values for a and b according to the following steps. 1. Determine how much space you can assign to clearance "c". For maintenance purposes, try to make "c" larger (1000 mm) rather than smaller (0 cm). The smaller "c" is, the larger "a" and "b" must be. 2. In the following floor loading table, find the column for "c" that most closely matches your value. If your "c" value is in between two table values, use the larger table value. Then, find the row for your floor load rating. Where the column and row intersect is the a+b value. 3. To determine clearance "a" and clearance "b", divide the a+b value between "a" and "b". They do not need to be equal. For example, if the a+b value from the table is 600 mm, then "a" can be 400 mm and "b" can be 200, or both "a" and "b" can be 300. 4. Calculate clearances by filling in and adding the table columns below: Clearance values Left (add down) a _________ Right (add down) b _________ Front (add down) c _________ Back (add down) Not applicable Plus minimum service clearance 100 mm (3.94 in) 100 mm (3.94 in) 1000 mm (39.4 in) 1000 mm (39.4 in) Equals total clearance 26 Site requirements

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
Calculate rack clearance dimensions as follows:
•
Clearance “a” is the space between the service clearance at the left side of the system (100 mm
minimum for installing the kickplate) and any other object, such as a desk or wall.
•
Clearance “b” is the space between the service clearance at the right side of the system (100
mm for the kickplate) and any other object.
•
Clearance “c” is the space between the service clearance at the front of the system and any
other object.
•
Use the value of “c” and your
fl
oor load rating to determine the values for a and b according to
the following steps.
1.
Determine how much space you can assign to clearance “c”. For maintenance purposes, try to
make “c” larger (1000 mm) rather than smaller (0 cm). The smaller “c” is, the larger “a” and
“b” must be.
2.
In the following
fl
oor loading table,
fi
nd the column for “c” that most closely matches your value.
If your “c” value is in between two table values, use the larger table value. Then,
fi
nd the row for
your
fl
oor load rating. Where the column and row intersect is the a+b value.
3.
To determine clearance “a” and clearance “b”, divide the a+b value between “a” and “b”. They
do not need to be equal. For example, if the a+b value from the table is 600 mm, then “a” can
be 400 mm and “b” can be 200, or both “a” and “b” can be 300.
4.
Calculate clearances by
fi
lling in and adding the table columns below:
Left
(add down)
Right
(add down)
Front
(add down)
Back
(add down)
Clearance values
a _________
b _________
c _________
Not applicable
Plus minimum
service clearance
100 mm (3.94 in)
100 mm (3.94 in)
1000 mm (39.4 in)
1000 mm (39.4 in)
Equals total
clearance
26
Site requirements