HP 8/8 Brocade Access Gateway Administrator's Guide v6.3.0 (53-1001345-01, Jul - Page 14

What’s new in this document - san switch manual

Get HP 8/8 PDF manuals and user guides View all HP 8/8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

All Fabric OS switches must be running v6.1.0 or later; all M-EOS switches must be running M-EOSc 9.1 or later, M-EOSn must be running 9.6.2 or later, and Cisco switches with SAN OS must be running 3.0 (1) and 3.1 (1) or later. Access Gateway supports 4 and 8 Gbit bladed servers and blades. Fabric OS v6.3.0 supports the following Brocade hardware platforms for Access Gateway: • Brocade 300 • Brocade 5100 • Brocade M5424 • Brocade 5450 • Brocade 5480 What's new in this document The following changes have been made since this document was last released: Information that was added: • Adaptive Networking is supported in AG - You can configure QoS for ingress rate limiting and SID/DID traffic prioritization for the following configurations: † Brocade HBA to AG to switch † Non-Brocade HBA to AG to switch † HBA (Brocade or Non-Brocade) to Edge AG to Core AG to switch • Support for Persistent ALPA - For servers that cannot handle changing addresses for the hosts and want the same PID across login sessions - Only supported when Access Gateway connects to a Brocade fabric. • Manual rebalance of F_Ports to distribute them among available N_Ports. • PG policy support for the following: - Login balancing within port groups. - Port group modes to allow F_Ports to connect to a specific port group For further information, refer to the release notes. xiv Access Gateway Administrator's Guide 53-1001345-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
xiv
Access Gateway Administrator’s Guide
53-1001345-01
All Fabric OS switches must be running v6.1.0 or later; all M-EOS switches must be running M-EOSc
9.1 or later, M-EOSn must be running 9.6.2 or later, and Cisco switches with SAN OS must be
running 3.0 (1) and 3.1 (1) or later. Access Gateway supports 4 and 8 Gbit bladed servers and
blades.
Fabric OS v6.3.0 supports the following Brocade hardware platforms for Access Gateway:
•
Brocade 300
•
Brocade 5100
•
Brocade M5424
•
Brocade 5450
•
Brocade 5480
What’s new in this document
The following changes have been made since this document was last released:
Information that was added:
•
Adaptive Networking is supported in AG
-
You can configure QoS for ingress rate limiting and SID/DID traffic prioritization for the
following configurations:
Brocade HBA to AG to switch
Non-Brocade HBA to AG to switch
HBA (Brocade or Non-Brocade) to Edge AG to Core AG to switch
•
Support for Persistent ALPA
-
For servers that cannot handle changing addresses for the hosts and want the same PID
across login sessions
-
Only supported when Access Gateway connects to a Brocade fabric.
•
Manual rebalance of F_Ports to distribute them among available N_Ports.
•
PG policy support for the following:
-
Login balancing within port groups.
-
Port group modes to allow F_Ports to connect to a specific port group
For further information, refer to the release notes.