HP 8/8 Brocade Access Gateway Administrator's Guide v6.3.0 (53-1001345-01, Jul - Page 75

Editing Company ID list if target devices on switch, Rejoining Fabric OS switches to a fabric

Get HP 8/8 PDF manuals and user guides View all HP 8/8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Rejoining Fabric OS switches to a fabric 4 3. Enter the following commands to enable the Flat FCID mode: vsan vsan# suspend no vsan vsan# suspend 4. Press Ctrl-Z to exit. 5. Enter the following command to save the MDS switch configuration: copy run start NOTE If there are any device(s) in the VSAN that you suspend, it takes that device offline until you unsuspend that VSAN. Editing Company ID list if target devices on switch If there are target devices on the switch, you must add the OUI of all the target devices present on the switch to the Company ID list, and then delete the OUI IDs of all the HBAs that are connected through the switch in Access Gateway mode from the Company ID list. You must remove the OUI IDs if and only if they are in the Company ID list. Use the following commands to determine if the OUIs in the Company ID list: switch#_show fcid-allocation area FCID area allocation company id info: 00:50:2E

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Access Gateway Administrator’s Guide
55
53-1001345-01
Rejoining Fabric OS switches to a fabric
4
3.
Enter the following commands to enable the Flat FCID mode:
vsan
vsan#
suspend
no vsan
vsan#
suspend
4.
Press
Ctrl-Z
to exit.
5.
Enter the following command to save the MDS switch configuration:
copy run start
NOTE
If there are any device(s) in the VSAN that you suspend, it takes that device offline until you
unsuspend that VSAN.
Editing Company ID list if target devices on switch
If there are target devices on the switch, you must add the OUI of all the target devices present on
the switch to the Company ID list, and then delete the OUI IDs of all the HBAs that are connected
through the switch in Access Gateway mode from the Company ID list. You must remove the OUI IDs
if and only if they are in the Company ID list. Use the following commands to determine if the OUIs
in the Company ID list:
switch#
_show fcid-allocation area
FCID area allocation company id info:
00:50:2E
<- Default entry
00:50:8B
00:60:B0
00:E0:79
00:0D:60 +
<- User -added entry
00:09:6B +
<- User -added entry
00:E0:8B *
<- Explicitly deleted entry (from the original default list)
Total company ids 6
+ - Additional user configured company ids
* -Explicitly deleted company ids from default list.
NOTE
You can also use the
Persistent FCID
field in the Cisco GUI tool to manually assign the FCIDs to
QLogic-based devices behind the Access Gateway module. If you use the method, ensure that
proper FCIDs are assigned, which have a different Area field from the target devices connected to
the same MDS switch.
Rejoining Fabric OS switches to a fabric
When a switch reboots after AG mode is disabled, the Default zone is set to no access. Therefore,
the switch does not immediately join the fabric to which it is connected. Use one of the following
methods to re-join a switch to the fabric:
•
If you saved a Fabric OS configuration before enabling AG mode, download the configuration
using the
configDownload
command.
•
If you want to re-join the switch to the fabric using the fabric configuration, use the following
procedure.