HP DL145 ProLiant DL100 Series Servers User Guide - Page 5

Operations, Power up the server, Remove the access panel

Get HP DL145 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 829160273594
View all HP DL145 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Operations Power up the server To power up the server, press the Power On button. Power down the server WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed. IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server. 1. Shut down the operating system as directed by the operating system documentation. 2. Press the Power On button to place the server in standby mode. When the server activates standby power mode, the system power LED changes from green to off. 3. Disconnect the power cords. The system is now without power. Remove the access panel 1. Power down the server (on page 5). 2. Extend and remove the server from the rack. 3. Remove the access panel: a. Loosen the thumbscrew or remove the screw that secures the access panel. b. Slide the access panel back about 1.5 cm (0.5 in). c. Lift and remove the access panel. NOTE: The server may look different from that shown. Operations 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Operations 5
Operations
Power up the server
To power up the server, press the Power On button.
Power down the server
WARNING:
To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On button
does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
IMPORTANT:
If installing a hot-plug device, it is not necessary to power down the server.
1.
Shut down the operating system as directed by the operating system documentation.
2.
Press the Power On button to place the server in standby mode. When the server activates standby
power mode, the system power LED changes from green to off.
3.
Disconnect the power cords.
The system is now without power.
Remove the access panel
1.
Power down the server (on page
5
).
2.
Extend and remove the server from the rack.
3.
Remove the access panel:
a.
Loosen the thumbscrew or remove the screw that secures the access panel.
b.
Slide the access panel back about 1.5 cm (0.5 in).
c.
Lift and remove the access panel.
NOTE:
The server may look different from that shown.