HP ElitePad Mobile POS G2 Maintenance and Service Guide - Page 84

Credit card reader, Release the credit card reader cable

Get HP ElitePad Mobile POS G2 PDF manuals and user guides View all HP ElitePad Mobile POS G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

7. Remove the right-side credit card reader board (3) and cable. Reverse this procedure to install the credit card reader boards. Credit card reader Description Credit card reader Spare part number 744026-001 Before removing the credit card reader, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet or the Retail Jacket. 3. Disconnect all external devices from the Retail Jacket. 4. Remove the top cap (see Top cap on page 63). 5. If installed, remove the tablet from the Retail Jacket (see Top cap on page 63). 6. Remove the front cover (see Front cover on page 65). Remove the credit card reader: 1. Disconnect the credit card reader cable (1) from the right-side credit card reader board. 2. Release the credit card reader cable (2) from the routing channel built into the rear cover. 3. Remove the two Phillips PM1.9×3.0 screws (3) that secure the retention tabs and the credit card reader to the rear cover. 4. Remove the two retention tabs (4). 76 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
7.
Remove the right-side credit card reader board
(3)
and cable.
Reverse this procedure to install the credit card reader boards.
Credit card reader
Description
Spare part number
Credit card reader
744026-001
Before removing the credit card reader, follow these steps:
1.
Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and
then shut it down through the operating system.
2.
Disconnect the power from the tablet by unplugging the power cord from the tablet or the Retail Jacket.
3.
Disconnect all external devices from the Retail Jacket.
4.
Remove the top cap (see
Top cap
on page
63
).
5.
If installed, remove the tablet from the Retail Jacket (see
Top cap
on page
63
).
6.
Remove the front cover (see
Front cover
on page
65
).
Remove the credit card reader:
1.
Disconnect the credit card reader cable
(1)
from the right-side credit card reader board.
2.
Release the credit card reader cable
(2)
from the routing channel built into the rear cover.
3.
Remove the two Phillips PM1.9×3.0 screws
(3)
that secure the retention tabs and the credit card reader
to the rear cover.
4.
Remove the two retention tabs
(4)
.
76
Chapter 5
Removal and replacement procedures