HP J4865A User Manual - Page 36

Horizontal Surface Mounting, Equipment, Cabinet, N o t e

Get HP J4865A PDF manuals and user guides View all HP J4865A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Installing the Series 4100gl Switches Installation Procedures 4. Install the other number 12-24 screw into the upper hole in each bracket. Tighten these screws. install and tighten the other 12-24 screws Installing the Series 4100gl Switches Equipment Cabinet Note Note If you are installing the switch in an equipment cabinet, in place of the 12-24 screws supplied with the switch, use the clips and screws that came with the cabinet. Plan which four holes you will be using in the cabinet and install all four clips and partially install the two bottom screws, as described in step 2 on the previous page, before proceeding to step 3. Horizontal Surface Mounting Place the switch on a table or other horizontal surface. Use a sturdy surface in an uncluttered area. You may want to secure the networking cables and switch power cord to the table legs or other part of the surface structure to help prevent people from tripping over the cords. Ensure the air flow is not restricted around the sides and back of the switch. 2-16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Installing the Series 4100gl Switches
Installation Procedures
4.
Install the other number 12-24 screw into the upper hole in each bracket.
Tighten these screws.
Installing the Series 4100gl
Switches
install and tighten the
other 12-24 screws
Equipment
Cabinet
N o t e
If you are installing the switch in an
equipment cabinet
, in place of the
12-24 screws supplied with the switch, use the clips and screws that came with
the cabinet. Plan which four holes you will be using in the cabinet and install
all four clips and partially install the two bottom screws, as described in step
2 on the previous page, before proceeding to step 3.
Horizontal Surface Mounting
Place the switch on a table or other horizontal surface. Use a sturdy surface
in an uncluttered area. You may want to secure the networking cables and
switch power cord to the table legs or other part of the surface structure to
help prevent people from tripping over the cords.
N o t e
Ensure the air flow is not restricted around the sides and back of the switch.
2-16