HP LH3000r HP Netserver LH 3/3r User Guide - Page 55

Type 1 and Type 2 --What You Need to Know to Determine Location, of the Slides

Get HP LH3000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LH3000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Chapter 8 Mounting the NetServer in a Rack Type 1 and Type 2 --What You Need to Know to Determine Location of the Slides To find the correct location for mounting the slides, you need to know the following: ◊ Note that the HP NetServer LH 3r is 8 EIA Units high. The mounting slides for the server attach first to the rack enclosure. Then the server attaches to the slides near its top. ◊ Unlike some slides, these (for the LH 3r) do not come apart. ◊ Use the template which is shipped with the server to measure where the slides will be located. Choose the template to use based on which rack type (refer to Figure 8-3) you have: ∗ use part number 5967-5201 for Type 1, the "Hewlett-Packard Rack System/E" rack ∗ use part number 5064-5869 for Type 2, the "Hewlett-Packard Systems" rack ◊ Note the base line of the server (the line where the bottom of the server will be when mounted). ◊ When marking, use tape or a marker pen to show the correct holes on each column. (Either Figure 8-7 or Figure 8-9 can be used to determine which holes are correct.) Do not place rack nuts in the holes, only mark them. Screws will be inserted through these holes into bar nuts to secure the mounting flange on the slide to the rack column. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Chapter 8
Mounting the NetServer in a Rack
47
Type 1 and Type 2 --What You Need to Know to Determine Location
of the Slides
To find the correct location for mounting the slides, you need to know the
following:
◊
Note that the HP NetServer LH 3r is 8 EIA Units high. The mounting
slides for the server attach first to the rack enclosure. Then the server
attaches to the slides near its top.
◊
Unlike some slides, these (for the LH 3r) do not come apart.
◊
Use the template which is shipped with the server to measure where
the slides will be located. Choose the template to use based on which
rack type (refer to Figure 8-3) you have:
use part number 5967-5201 for Type 1, the "Hewlett-Packard Rack
System/E" rack
use part number 5064-5869 for Type 2, the "Hewlett-Packard
Systems" rack
◊
Note the base line of the server (the line where the bottom of the
server will be when mounted).
◊
When marking, use tape or a marker pen to show the correct holes on
each column. (Either Figure 8-7 or Figure 8-9 can be used to
determine which holes are correct.) Do not place rack nuts in the
holes, only mark them. Screws will be inserted through these holes
into bar nuts to secure the mounting flange on the slide to the rack
column.