HP LH3000r HP Netserver LH 3/3r User Guide - Page 76

Con Mass Storage: The HP NetServer is shipped with the hot-swap

Get HP LH3000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LH3000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Chapter 10 Configuring the NetServer Novell NetWare / IntranetWare or Microsoft Windows NT Server on a factory-configured NetServer. This installation also loads the Local Support Tool onto Windows NT or NetWare systems. The Local Support Tool is a stand-alone support tool accessed directly from the NetServer. It gives you information to help you manage the NetServer. ◊ Select No for manual NOS installation. Perform a manual NOS installation if you are installing a NOS other than certain versions of Novell NetWare / IntranetWare or Microsoft Windows NT Server, or if you have replaced any HP components. • View Configuration Advisories: Read the configuration advisories, and print them if necessary. You can change your hardware at this time to conform to the advisories. • Configure Remote Management: This utility configures the Integrated Remote Management device for remote management. It enables remote, dial-up server management. To configure Integrated Remote Assistant, select Configure Remote Management on the Configure Remote Management screen. • Show System Information: Use this screen to display information about standard and accessory boards and devices in the system, as well as the used and available system resources. ◊ Select View System Information on the Show System Information screen to display information about standard and accessory boards and devices in the system. ◊ Select View Resources on the Show System Information screen to display used and available system resources, such as memory ranges, I/O port ranges, DMA channels, and interrupt (IRQ) levels. • Configure Mass Storage: The HP NetServer is shipped with the hot-swap drive unconfigured. Do ONE of the following: 1. Run HP NetRAID Assistant to configure one or more RAID logical drives. Select "Execute" on the Configure Disk Array screen to start the HP NetRAID Assistant. For more information, refer to the Integrated HP NetRAID Controller Configuration Guide. 2. Exclude SCSI A channel from the integrated HP NetRAID controller, as follows: a. Restart the HP NetServer. 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Chapter 10
Configuring the NetServer
68
Novell NetWare / IntranetWare or Microsoft Windows NT Server on a
factory-configured NetServer. This installation also loads the Local
Support Tool onto Windows NT or NetWare systems. The Local
Support Tool is a stand-alone support tool accessed directly from the
NetServer. It gives you information to help you manage the NetServer.
◊
Select No for manual NOS installation. Perform a manual NOS
installation if you are installing a NOS other than certain versions of
Novell NetWare / IntranetWare or Microsoft Windows NT Server, or
if you have replaced any HP components.
•
View Configuration Advisories: Read the configuration advisories, and
print them if necessary. You can change your hardware at this time to
conform to the advisories.
•
Configure Remote Management: This utility configures the Integrated
Remote Management device for remote management. It enables remote,
dial-up server management. To configure Integrated Remote Assistant,
select Configure Remote Management on the Configure Remote
Management screen.
•
Show System Information: Use this screen to display information about
standard and accessory boards and devices in the system, as well as the
used and available system resources.
◊
Select View System Information on the Show System Information
screen to display information about standard and accessory boards and
devices in the system.
◊
Select View Resources on the Show System Information screen to
display used and available system resources, such as memory ranges,
I/O port ranges, DMA channels, and interrupt (IRQ) levels.
•
Configure Mass Storage: The HP NetServer is shipped with the hot-swap
drive unconfigured. Do ONE of the following:
1.
Run HP NetRAID Assistant to configure one or more RAID logical
drives. Select "Execute" on the Configure Disk Array screen to start
the HP NetRAID Assistant. For more information, refer to the
Integrated HP NetRAID Controller Configuration Guide
.
2.
Exclude SCSI A channel from the integrated HP NetRAID controller,
as follows:
a.
Restart the HP NetServer.