HP Pro Tower 400 G9 PCI Desktop PC Maintenance and Service Guide - Page 30

To install the optical drive, reverse the removal procedure.

Get HP Pro Tower 400 G9 PCI Desktop PC PDF manuals and user guides View all HP Pro Tower 400 G9 PCI Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

2. Push the green release latch on the back of the drive (2), and then slide the drive forward and out of the front of the computer (3). 3. If you are installing an optical drive in a bay covered by a bezel blank, remove the front bezel (Front bezel on page 24), and then remove the bezel blank (Bezel blanks on page 25). 4. Install the release latch onto the drive. Align the small pin on the release latch with the small hole on the side of the drive and press the latch firmly onto the drive. 5. Connect the power cable and data cable to the rear of the drive, and then connect the opposite end of the data cable to one of the SATA connectors labeled SATA1 or SATA2 on the system board. To install the optical drive, reverse the removal procedure. When installing an optical drive, connect the power cable and data cable to the rear of the drive, and then connect the opposite end of the data cable to one of the SATA connectors labeled SATA1 or SATA2 on the Optical drive 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
2.
Push the green release latch on the back of the drive
(2)
, and then slide the drive forward and out of the
front of the computer
(3)
.
3.
If you are installing an optical drive in a bay covered by a bezel blank, remove the front bezel (
Front bezel
on page
24
), and then remove the bezel blank (
Bezel blanks
on page
25
).
4.
Install the release latch onto the drive. Align the small pin on the release latch with the small hole on the
side of the drive and press the latch firmly onto the drive.
5.
Connect the power cable and data cable to the rear of the drive, and then connect the opposite end of the
data cable to one of the SATA connectors labeled SATA1 or SATA2 on the system board.
To install the optical drive, reverse the removal procedure.
When installing an optical drive, connect the power cable and data cable to the rear of the drive, and then
connect the opposite end of the data cable to one of the SATA connectors labeled SATA1 or SATA2 on the
Optical drive
23