Home » HP Manuals » Laptops » HP ProBook 4525s » Manual Viewer

HP ProBook 4525s HP ProBook Notebook PC User Guide - Linux - Page 89

Setting a DriveLock password, Security, DriveLock passwords, Enable, Protection, New password

Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

To apply DriveLock protection to an internal hard drive, a user password and a master password must be set in Computer Setup. Note the following considerations about using DriveLock protection: ● After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering either the user password or the master password. ● The owner of the user password should be the day-to-day user of the protected hard drive. The owner of the master password may be either a system administrator or the day-to-day user. ● The user password and the master password can be identical. ● You can delete a user password or master password only by removing DriveLock protection from the drive. DriveLock protection can be removed from the drive only with the master password. Setting a DriveLock password To access the DriveLock settings in Computer Setup, follow these steps: 1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select Security > DriveLock passwords, and then press enter. 3. Select the location of the hard drive you want to protect, and then press f10. 4. Use the arrow keys to select Enable in the Protection field, and then press f10. 5. Read the warning. To continue, press f10. 6. Type your user password in the New password and Verify new password fields, and then press f10. 7. Type your master password in the New password and Verify new password fields, and then press f10. 8. To confirm DriveLock protection on the drive you have selected, type DriveLock in the confirmation field, and then press f10. 9. To exit DriveLock settings, use the arrow keys to select Esc. 10. To save your preferences, use the arrow keys to select File > Save changes and exit. Then follow the instructions on the screen. Your preferences go into effect when the computer restarts. Entering a DriveLock password Be sure that the hard drive is inserted into the computer (not into an optional docking device or external MultiBay). At the DriveLock Password prompt, type your user or master password (using the same kind of keys you used to set the password), and then press enter. After 2 incorrect attempts to enter the password, you must shut down the computer and try again. Changing a DriveLock password To access the DriveLock settings in Computer Setup, follow these steps: 1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select Security > DriveLock passwords, and then press enter. Using passwords 79

Section	Page
Features	11
Identifying hardware	11
Top components	11
TouchPad	11
Lights	12
Buttons, speakers, switches, and fingerprint reader (select models only)	13
Keys	15
Front components	16
Right-side components	16
Left-side components	17
Bottom components	19
Display	19
Wireless antennas (select models only)	20
Additional hardware components	22
Identifying the labels	22
Pointing devices and keyboard	24
Using pointing devices	24
Setting pointing device preferences	24
Connecting an external mouse	24
Using the keyboard	24
Using hotkeys	24
Initiating Sleep	25
Decreasing screen brightness	25
Increasing screen brightness	25
Switching the screen image	26
Opening the default e-mail application	26
Opening the default Web browser	26
Muting speaker sound	26
Decreasing speaker sound	26
Increasing speaker sound	26
Playing the previous track or section of an audio CD or a DVD	26
Playing, pausing, or resuming an audio CD or a DVD	26
Playing the next track or section of an audio CD or a DVD	27
Using the embedded numeric keypad	27
Enabling and disabling the embedded numeric keypad	27
Switching key functions on the embedded numeric keypad	27
Using an optional external numeric keypad	27
Cleaning the TouchPad and keyboard	27
Multimedia	29
Multimedia features	29
Identifying your multimedia components	29
Adjusting the volume	30
Multimedia software	31
Accessing your preinstalled multimedia software	32
Installing multimedia software from a disc	32
Audio	32
Connecting external audio devices	32
Checking your audio functions	33
Video	33
Connecting an external monitor or projector	33
Using the external monitor port	33
Using the HDMI port	34
Optical drive (select models only)	35
Using optical discs (CDs, DVDs, and BDs)	35
Selecting the right disc (CDs, DVDs, and BDs)	36
CD-R discs	36
CD-RW discs	36
DVD±R discs	37
DVD±RW discs	37
LightScribe DVD+R discs	37
Blu-ray Discs (BDs)	37
Playing a CD, DVD, or BD	37
Observing the copyright warning	38
Copying a CD or DVD	38
Removing an optical disc (CD, DVD, or BD)	38
The optical disc tray does not open for removal of a CD, DVD, or BD	39
Webcam	40
Power management	41
Setting power options	41
Using power-saving states	41
Initiating and exiting Suspend	41
Initiating and exiting Hibernation	41
Using the Power icon	42
Using power management	42
Viewing the current power management settings	42
Changing the current power management settings	42
Using external AC power	42
Connecting the AC adapter	43
Using battery power	43
Inserting or removing the battery	44
Charging a battery	45
Maximizing battery discharge time	46
Managing low battery levels	46
Identifying low battery levels	46
Resolving a low battery level	46
Resolving a low battery level when external power is available	46
Resolving a low battery level when a charged battery is available	47
Resolving a low battery level when no power source is available	47
Resolving a low battery level when the computer cannot exit Hibernation	47
Calibrating a battery	47
Step 1: Fully charge the battery	47
Step 2: Disable Hibernation and Suspend	48
Step 3: Discharge the battery	48
Step 4: Fully recharge the battery	48
Step 5: Reenable Hibernation and Suspend	49
Conserving battery power	49
Storing a battery	49
Disposing of a used battery	49
Replacing the battery	50
Testing an AC adapter	50
Shutting down the computer	50
Drives	52
Handling drives	52
Using external drives	52
Using optional external devices	53
Replacing the hard drive	53
External devices	67
Using a USB device	67
Connecting a USB device	67
Removing a USB device	67
Using USB legacy support	68
Using an eSATA device	68
Connecting an eSATA device	68
Stopping and removing an eSATA device	69
Using external drives	69
Using optional external devices	69
External media cards	71
Using Media Card Reader cards	71
Inserting a digital card	71
Removing a digital card	72
Using ExpressCards (select models only)	72
Configuring an ExpressCard	72
Inserting an ExpressCard	72
Removing an ExpressCard	73
Memory modules	75
Adding or replacing memory modules	75
Security	86
Protecting the computer	86
Using passwords	86
Setting passwords in the operating system	87
Setting passwords in Computer Setup	87
Setup password	87
Managing a setup password	88
Entering a setup password	88
Using Computer Setup DriveLock	88
Setting a DriveLock password	89
Entering a DriveLock password	89
Changing a DriveLock password	89
Removing DriveLock protection	90
Using Computer Setup security features	90
Securing system devices	90
Using Computer Setup stringent security	90
Setting stringent security	91
Removing stringent security	91
Viewing Computer Setup System Information	91
Using firewall software	92
Setting up automatic online updates	92
Installing a security cable	92
Computer Setup	94
Starting Computer Setup	94
Using Computer Setup	94
Navigating and selecting in Computer Setup	94
Restoring factory settings in Computer Setup	95
Computer Setup menus	95
File menu	95
Security menu	95
Diagnostics menu	96
System Configuration menu	97

Match case Limit results 1 per page

To apply DriveLock protection to an internal hard drive, a user password and a master password must

be set in Computer Setup. Note the following considerations about using DriveLock protection:

●

After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering

either the user password or the master password.

●

The owner of the user password should be the day-to-day user of the protected hard drive. The

owner of the master password may be either a system administrator or the day-to-day user.

●

The user password and the master password can be identical.

●

You can delete a user password or master password only by removing DriveLock protection from

the drive. DriveLock protection can be removed from the drive only with the master password.

Setting a DriveLock password

To access the DriveLock settings in Computer Setup, follow these steps:

Open Computer Setup by turning on or restarting the computer, and then pressing

f10

while the

“F10 = ROM Based Setup” message is displayed in the lower-left corner of the screen.

Use the arrow keys to select

Security

DriveLock passwords

, and then press

enter

Select the location of the hard drive you want to protect, and then press

f10

Use the arrow keys to select

Enable

in the

Protection

field, and then press

f10

Read the warning. To continue, press

f10

Type your user password in the

New password

and

Verify new password

fields, and then press

f10

Type your master password in the

New password

and

Verify new password

fields, and then

press

f10

To confirm DriveLock protection on the drive you have selected, type

DriveLock

in the

confirmation field, and then press

f10

To exit DriveLock settings, use the arrow keys to select

Esc

10.

To save your preferences, use the arrow keys to select

File

Save changes and exit

. Then follow

the instructions on the screen.

Your preferences go into effect when the computer restarts.

Entering a DriveLock password

Be sure that the hard drive is inserted into the computer (not into an optional docking device or external

MultiBay).

At the

DriveLock Password

prompt, type your user or master password (using the same kind of keys

you used to set the password), and then press

enter

After 2 incorrect attempts to enter the password, you must shut down the computer and try again.

Changing a DriveLock password

To access the DriveLock settings in Computer Setup, follow these steps:

Open Computer Setup by turning on or restarting the computer, and then pressing

f10

while the

“F10 = ROM Based Setup” message is displayed in the lower-left corner of the screen.

Use the arrow keys to select

Security

DriveLock passwords

, and then press

enter

Using passwords