HP ProLiant DL288 Configuring Arrays on HP Smart Array Controllers Reference G - Page 13

BIOS Serial Console & EMS>BIOS Interface Mode., In RBSU, select

Get HP ProLiant DL288 PDF manuals and user guides View all HP ProLiant DL288 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

If the BIOS interface is in Auto mode, change it to Command Line mode as follows: a. Press the F9 key to open RBSU when prompted during POST. b. In RBSU, select BIOS Serial Console & EMS>BIOS Interface Mode. c. Change the setting to Command Line. d. Press the Esc key to exit RBSU, and then press the F10 key to confirm that you want to exit. The server reboots, and POST runs again. During POST, all controllers in the server are initialized one at a time in the current boot order sequence. If a controller is connected to one or more hard drives, a message appears during the initialization process for that controller, prompting you to start ORCA. 2. At the ORCA prompt for the controller that you want to configure, press the F8 key. The ORCA command line prompt appears. 3. Enter the command for the task that you want to perform. For information about command syntax and to see a list of possible commands, enter help. 4. If you create a logical drive, format it when you install the operating system. If the operating system is already installed, follow the instructions for formatting logical drives that are given in the operating system documentation. Option ROM Configuration for Arrays 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Option ROM Configuration for Arrays
13
If the BIOS interface is in Auto mode, change it to Command Line mode as follows:
a.
Press the
F9
key to open RBSU when prompted during POST.
b.
In RBSU, select
BIOS Serial Console & EMS>BIOS Interface Mode.
c.
Change the setting to Command Line.
d.
Press the
Esc
key to exit RBSU, and then press the
F10
key to confirm that you want to exit.
The server reboots, and POST runs again.
During POST, all controllers in the server are initialized one at a time in the current boot order
sequence. If a controller is connected to one or more hard drives, a message appears during the
initialization process for that controller, prompting you to start ORCA.
2.
At the ORCA prompt for the controller that you want to configure, press the
F8
key.
The ORCA command line prompt appears.
3.
Enter the command for the task that you want to perform. For information about command syntax
and to see a list of possible commands, enter
help
.
4.
If you create a logical drive, format it when you install the operating system. If the operating system
is already installed, follow the instructions for formatting logical drives that are given in the operating
system documentation.