HP StorageWorks 16-EL HP StorageWorks SAN Switch 2/16 Fabric OS V3.1.2 Release - Page 26

Table 4, Version 3.1.2 Error Messages Not Previously Available Continued, Severity & Message

Page 26 highlights

Documentation Updates Table 4: Version 3.1.2 Error Messages Not Previously Available (Continued) Severity & Message Critical DIAG-ERRSTAT(CRL), 1 Critical DIAG-ERRSTAT (DISCC3), 1 Critical DIAG-ERRSTAT (ENCIN), 1 Probable Cause Port Error Statistics counter is nonzero, meaning that a Cyclic redundancy check on frame failed error was detected when receiving frames. This can be caused by a faulty cable or deteriorated SFP. It can also indicate deeper problems in the motherboard or ASIC. This message is generated by the portloopbacktest command, if problems are found. Port Error Statistics counter is nonzero, meaning that a Discarded Class 3 frames error was detected when receiving frames. This can be caused by a faulty cable or deteriorated SFP. It can also indicate deeper problems in the motherboard or ASIC. This message is generated by the portloopbacktest or spinsilk commands, if problems are found. Port Error Statistics counter is nonzero, meaning that an Encoding error, inside frame error was detected when receiving frames. This can be caused by a faulty cable or deteriorated SFP. It can also indicate deeper problems in the motherboard or ASIC. This message is generated by the portloopbacktest or spinsilk commands, if problems are found. Recommended Action Check for a faulty cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8 EL, you must replace the entire switch. Check for a faulty cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8 EL, you must replace the entire switch. Check for a faulty cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8 EL, you must replace the entire switch. 26 SAN Switch 2/16 Fabric OS 3.1.2 Release Notes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

Documentation Updates
26
SAN Switch 2/16 Fabric OS 3.1.2 Release Notes
Critical
DIAG-ERRSTAT(CRL), 1
Port Error Statistics counter is
nonzero, meaning that a
Cyclic
redundancy check on frame
failed
error was detected when
receiving frames. This can be
caused by a faulty cable or
deteriorated SFP. It can also indicate
deeper problems in the
motherboard or ASIC. This message
is generated by the
portloopbacktest
command,
if problems are found.
Check for a faulty cable or
deteriorated SFP. Replace the
cable or SFP if necessary.
If the problem persists:
For the SAN Switch 2/16,
replace the motherboard FRU.
For the SAN Switch 2/8 EL, you
must replace the entire switch.
Critical
DIAG-ERRSTAT (DISCC3), 1
Port Error Statistics counter is
nonzero, meaning that a
Discarded Class 3
frames
error was detected when receiving
frames. This can be caused by a
faulty cable or deteriorated SFP. It
can also indicate deeper problems
in the motherboard or ASIC. This
message is generated by the
portloopbacktest
or
spinsilk
commands, if problems
are found.
Check for a faulty cable or
deteriorated SFP. Replace the
cable or SFP if necessary.
If the problem persists:
For the SAN Switch 2/16,
replace the motherboard FRU.
For the SAN Switch 2/8 EL, you
must replace the entire switch.
Critical
DIAG-ERRSTAT (ENCIN), 1
Port Error Statistics counter is
nonzero, meaning that an
Encoding error, inside
frame
error was detected when
receiving frames. This can be
caused by a faulty cable or
deteriorated SFP. It can also indicate
deeper problems in the
motherboard or ASIC. This message
is generated by the
portloopbacktest
or
spinsilk
commands, if problems
are found.
Check for a faulty cable or
deteriorated SFP. Replace the
cable or SFP if necessary.
If the problem persists:
For the SAN Switch 2/16,
replace the motherboard FRU.
For the SAN Switch 2/8 EL, you
must replace the entire switch.
Table 4:
Version 3.1.2 Error Messages Not Previously Available (Continued)
Severity & Message
Probable Cause
Recommended Action