HP Tc2100 hp server tc2100 NOS installation guide (English)
HP Tc2100 - Server - 128 MB RAM Manual
View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Tc2100 manual content summary:
- HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 1
HP Server tc2100 Network Operating System Installation Guide For: Microsoft Windows NT 4.0 Server Microsoft Windows 2000 Server and Microsoft Small Business Server 2000 Novell NetWare 5.1 and Novell Small Business Suite 5.1 Red Hat Linux 7.1 TurboLinux Server 6.5 HP Part Number P4648-90002 Printed - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 2
that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another of Red Hat Software, Incorporated. Adaptec is a trademark of Adaptec, Incorporated. Hewlett-Packard Company Network Server Division Technical Communications/MS - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 3
HP NetRAID-1M Adapter 13 Troubleshooting 13 Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration 13 Tip #2. NT Warning About Drives with More than 1024 Cylinders 14 Tip #3. Service Pack Files Replaced Without Feedback 15 Tip #4. Using the NT Event Log to Diagnose Network Adapter Problems - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 4
Adding Terminal Server Services 22 Section 2. Configure the network 23 PHASE 1 - Configure Server IP Address Service Pack 26 PHASE 2 - Install the HP Video Driver 27 PHASE 3 - Install the HP LAN driver 27 PHASE 4 - Install Windows 2000 Recovery Console 28 Troubleshooting 28 Tip #1. Upgrading - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 5
PHASE 4- Install the Support Pack 39 Troubleshooting 40 Tip #1. Restarting NetWare Installation 40 On-Line Information and Software Sources 40 5 Configure the Server 41 PHASE 3 - Complete the Installation 42 On-Line Information and Software Sources 43 6 Installing TurboLinux Server 6.5 45 - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 6
- HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 7
HP server following the instructions in the HP Server tc2100 Installation Guide. It is recommended that you do not install any third party adapter until you verify that the HP equipment is functioning properly and you complete the NOS installation. Preparing your Hard Disk Drives The HP Tower Server - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 8
tc2100 system may be used as follows: Startup CD Usage Method 1 Method 2 Method 3 Insert CD in your new HP server and reboot it. This will run HP Diagtools (a DOS program) Insert the CD in a Windows or Linux PC. Open the file start.htm. This allows you to access manuals and create drivers - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 9
Create the Drivers Diskettes 1. Locate two blank, formatted 3.5" diskettes. 2. Insert your HP Startup CD in a Windows PC and follow the on-screen instructions to create the following diskettes: o HP Server tc2100 Windows NT SCSI driver (HP disk NT#1) o HP Server tc2100 Windows NT LAN driver (HP disk - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 10
are required to install Microsoft Windows NT 4.0 on your server. Follow these steps to create these installation diskettes: 1. Phase 5 - Completing the Installation • Phase 6 - Install the Service Pack • Phase 7 - Install the HP Video Driver NOTE Do not try to install Windows NT 4.0 via booting - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 11
option "Other (Requires Disk provided by a hardware manufacturer)". d. When prompted to insert the "Manufacturer-supplied hardware support disk", insert the HP Server tc2100 Windows NT SCSI driver (HP disk NT#1) into floppy drive then press Enter e. Press Enter to select the "Adaptec Ultra160 Family - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 12
reconfigured your new HP server to use a hard drive already containing data. 3. Insert Windows NT Server Setup screen will display the system hardware and software components it Enter to have Setup examine your hard disks. 12. Insert the HP Server tc2100 Windows NT SCSI driver (HP disk NT#1) when - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 13
Adapter drivers, to use HP specific driver b. Insert the HP Server tc2100 Windows NT LAN driver (HP disk NT#2) then press Enter c. Press Enter to validate the selection of the "Intel® PRO Adapter", then Enter again to confirm the Network Adapters selection. 5. Follow the on-screen instructions to - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 14
SQL Server Drivers) then press OK 3. Set the Time zone, Date, and Time then select Close. 4. You will be notified that a standard VGA video driver has been installed. Do not attempt to install the HP high-resolution video driver at this time because they would be overwritten by the service pack - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 15
CD-ROM. It allows you to install the Service Pack from the CD-ROM drive of your HP server. o You may contact Microsoft Support at (800) 936 5900 or (800) 426 9400 to have a Service Pack CD-ROM shipped to you. 2. To install the Service Pack, login on your HP server as the Administrator, then run the - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 16
If you would like to make use of the high-resolution video driver, follow these steps: 1. Ensure Microsoft Windows NT Service Pack (version #6a or above) is installed. This is a REQUIREMENT. 2. Logon as the Administrator on your HP server then insert HP Startup CD in the CD-ROM drive. The Startup CD - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 17
NT Reference Manual for help. NOTE Windows NT Event Viewer may have recorded network errors if your HP server was not connected prior to your login. If you can not resolve the problem please contact your HP service representative or use HP website for additional troubleshooting resources. 2. Run - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 18
an example the installation of an additional HP 10/100TX PCI LAN Adapter (HP product number D5013B) - this HP accessory is supported on your HP Server tc2100. 1. Open Start | Settings | Control Panel | Network | Adapters. 2. Select Add. 3. As HP provides a specific driver, click Have Disk when given - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 19
restart the system at this point, the HP NetRAID1M Adapter driver will not be present in the driver list until the next system boot. Troubleshooting This section will help you resolve some of the most common installation problems. Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration The boot - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 20
menu." Appears. Follow the instructions on the screen to specifically for conflicts with parts of the existing system configuration that are not being changed. If you cannot determine the source of the error, contact the host adapter vendor or HP Technical Support correct this problem, perform the - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 21
that you apply the service pack again if you make any changes. Tip #4. Using the NT Event Log to Diagnose Network Adapter Problems If the Network Adapter driver fails to start or does not appear to be working correctly, examine the Event Log for any driver diagnostic messages. 1. Start the - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 22
Chapter 2 Installing Microsoft Windows NT 4.0 Server On-Line Information and Software Sources • HP World Wide Web access: http://www.hp.com • Microsoft World Wide Web access: http://www.microsoft.com • Microsoft Product Support Services: http://support.microsoft.com/directory • Windows NT - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 23
Chapter 1 "Preparing your HP Server tc2100 for your NOS installation" for our recommendations on the server preparation. Then gather the following material: • HP Server tc2100 Startup CD • Microsoft Windows 2000 CD-ROM1 as well as the latest Microsoft Windows 2000 Service Pack (#2 or above). • Six - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 24
manually specify you adapter: a. Press S (to Specify Additional Device). b. When prompted to insert driver diskette, please insert the HP NetRAID1M driver from step 1 above. 4. Press Enter to continue at the "Windows 2000 Server Setup - Welcome to Setup" Screen. 5. Press C to continue Setup at - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 25
Server and Small Business Server 2000 b. At the "Create partition size" prompt, type 2048 and press Enter. c. HP NetRAID-1M driver, Windows setup will prompt for the driver diskette again. 12 Microsoft 2000 manuals should you need instructions to logon (press Ctrl-Alt-Del). Enter - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 26
(!) or (?). Use the "Device Status" message for troubleshooting. Or if a printer is available, use the View, Print from the menu to get a report. 3. Verify if the installed drivers are digitally signed. a. In the Device Manager, select the device (e.g HP NetRAID-1M) that you want to verify. b. Right - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 27
Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 NOTE Windows 2000 Event Viewer may 3. The "Write signature and Upgrade" wizard will start if you have new hard drives with no signatures on them. Follow the on-screen instructions to create this signature. 4. Select - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 28
". 3. Scroll to and click "Terminal Services" checkbox then click Next. 4. Select the mode you want to use: "Remote administration mode" or "Application sever mode" then click Next. NOTE The following instructions are based on the Application server mode. Please note the licensing requirement - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 29
No). 7. Insert following diskette(s) when prompted and follow screen instructions. 8. Click OK when the installation is completed then shutdown My Network Places | Properties | Local Area Connection on your HP server. NOTE If you HP server host several Network adapters, the window will show one " - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 30
and Test Network Link 1. Create shares: create a folder on your HP server hard drive then share it (right click Sharing). 2. Create users computername is the server name you entered during Windows NT installation. You should get four reply's from your new server. If there is a link problem it must - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 31
Programs | Administrative Tools | Configure Your Server to open the "Windows 2000 Configure Your Server" window. 2. Select "Active Directory". 3. Scroll down and click "Start the Active Directory wizard". 4. Click Next to continue. NOTE The following instructions corresponds to the standard steps - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 32
Pack from the CD-ROM drive of your HP server. o You may contact Microsoft Support at (800) 936 5900 or (800) 426 9400 to have a Service Pack CD-ROM shipped to you. 2. To install the Service Pack, logon on your HP server as the "Administrator", then run the Service Pack on your system. 3. If prompted - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 33
driver, follow these steps: 1. Ensure Microsoft Windows 2000 Service Pack (version #2 or above) is installed. This is a REQUIREMENT. 2. Logon as the "Administrator" on your HP Server tc2100 then insert HP you upgrade the driver using the HP Startup CD: 1. Insert the HP Startup CD in your new server. - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 34
refer to Tip#6 in the Troubleshooting section. Troubleshooting This section will help you resolve some of the most common installation problems. Tip #1. Upgrading from NT 4.0 to Windows 2000 It is possible to upgrade from any edition of NT 4.0 including Terminal Server to Windows 2000. Please refer - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 35
Server and Small Business Server 2000 The cause of this problem is that the NTLOADER is encountering a duplicate hard drive signature. This signature is calculated by the NTLOADER code after reading a specific . (This version supports FAT32, which works HP recommends that you F2 during power on self - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 36
create the Windows 2000 driver diskette: a. Boot your server (or any PC system) with the Netserver Navigator in the CD-ROM. b. Go to the Diskette Library from the main menu and follow on-screen instructions. NOTE Please consult the "HP NetRAID-1m installation guide" for instructions on doing the - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 37
(this might happen after installing a new driver, component, software, etc), Windows 2000 provides the following recovery options to help you gain access to your Windows 2000 installation to replace damaged files and services for troubleshooting purpose. HP therefore recommends that you install the - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 38
Server and Small Business Server 2000 4. Command prompt. Provides an alternate command shell CMD.EXE instead of the explorer. This is dictated by the registry key: hklm\system\CurrentControlSet\Control\SafeBoot\AlternateShell There is a Safe-Mode boot loophole. Since NTLDR loads "Boot Load" drivers - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 39
erase all data and partitions from your hard drive. Then resume all installation process. On-Line Information and Software Sources • HP World Wide Web access: http://www.hp.com • Microsoft World Wide Web access: http://www.microsoft.com • Microsoft Product Support Services: http://support.microsoft - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 40
- HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 41
test network link. 6. Install Windows Terminal Services (optional). Section 1. Run HP Diagtools (optional) To perform HP Diagtools hardware diagnostic on your HP Server tc2100, switch off your HP server then reboot on the Startup CD and follow the on-screen instructions. View and save the hardware - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 42
Insert your HP Startup CD in a Windows PC and follow the on-screen instructions to create the HP Server tc2100 NetWare SCSI and LAN drivers (HP disk Partition". 4. HP recommends accepting the default 100MB boot partition by pressing Enter to continue. 5. If you accept erasing all data on your disk - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 43
Small Business Suite 5/5.1 5. Press Enter to setup "a new server" then scroll down and choose Continue. 6. Modify or accept the server settings, the regional settings, as well as the mouse and video configuration. PHASE 2 - Install HP Drivers 1. The installation program then detect your hardware and - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 44
f. Press F3 and specify the path: A:\SCSI then press Enter. g. The installation program takes a few seconds then automatically add the HP driver on the driver list. NOTE The new HP driver may show the same device name description but is a more recent version. h. Scroll down and select "Return to - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 45
proceeds under a graphical interface. Follow the on-screen instructions to configure your network: server name, IP adress, Host name and domain, etc. You will need to mount the Novell Consolidated Support Pack as a NetWare volume. 2. Insert the NetWare Support Pack CD-ROM. 3. Close the GUI. 4. - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 46
. Troubleshooting Tip #1. Restarting NetWare Installation If you want to restart NetWare installation from the very beginning, use a utility such as fdisk to erase all data and partitions from your hard drive. Then resume all installation process. On-Line Information and Software Sources • HP - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 47
Hat Linux 7.1 Prepare the Installation Please refer to the Chapter 1 "Preparing your HP Server tc2100 for your NOS installation" for our recommendations on the server preparation. Then gather the following material: • HP Server tc2100 Startup CD • Red Hat Linux 7.1 CD-ROMs #1 and #2 • Two or more - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 48
manually the selection as your HP Server tc2100 comes with a ATI Rage XL AGP video chip. o You can find HP monitors references on the back of your monitor. o HP . 3. HP recommends that you create a boot diskette that will allow you to boot and manage your server when experiencing problems in loading - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 49
Chapter 5 Installing Red Hat Linux 7.1 On-Line Information and Software Sources • HP World Wide Web access: http://www.hp.com • Red Hat World Wide Web access: http://www.Red Hat.com • Red Hat Errata World Wide Web access: http://www.Red Hat.com/errata 43 - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 50
- HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 51
Installation Please refer to the Chapter 1 "Preparing your HP Server tc2100 for your NOS installation" for our recommendations on the server preparation. Then gather the following material: • HP Server tc2100 Startup CD • TurboLinux Server 6.5 CD-ROM • A blank 3.5-inch diskette, labeled TurboLinux - HP Tc2100 | hp server tc2100 NOS installation guide (English) - Page 52
manuals should you need further details on the networking settings. • HP HP monitors references on the back of your monitor. o HP Server tc2100 specific TurboLinux CD-ROMs. 3. HP recommends that you create a boot diskette that will allow you to boot and manage your server when experiencing problems
HP Server tc2100
Network Operating System
Installation Guide
For:
Microsoft Windows NT 4.0 Server
Microsoft Windows 2000 Server and Microsoft Small
Business Server 2000
Novell NetWare 5.1 and Novell Small Business Suite 5.1
Red Hat Linux 7.1
TurboLinux Server 6.5
HP Part Number P4648-90002
Printed August 2001