HP Tc2100 hp server tc2100 NOS installation guide (English) - Page 19

HP NetRAID-1M Adapter, Troubleshooting, Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Chapter 2 Installing Microsoft Windows NT 4.0 Server NOTE The installation of the new network adapter will not take effect until you restart the server. If you want to implement Adapter Teaming (requires 2 Network Adapters), Windows NT 4.0 Service Pack version 6a or above is required. If there are errors during the installation, you should verify you installed the correct driver for your adapter. HP NetRAID-1M Adapter 1. Create the HP NetRAID driver for Windows NT diskette using the Navigator CD provided with your NetRAID card. You may refer to the NetRAID card manuals or HP Navigator CD for additional details. 2. Open Control Panel | SCSI Adapters | Drivers tab. 3. Select Add. 4. Click Have Disk when given a list of SCSI Adapters drivers then browse the A: drive to locate the appropriate NetRAID-1M driver (in directory A:\NETRAID). Click OK to install it. 5. Select the "Hewlett-Packard NetRAID 1M Adapter", and click OK. 6. In the System Settings Change windows, click Yes to restart Windows NT. NOTE If you do not restart the system at this point, the HP NetRAID1M Adapter driver will not be present in the driver list until the next system boot. Troubleshooting This section will help you resolve some of the most common installation problems. Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration The boot manager for Windows NT contains recovery logic to allow you to return to the last known good configuration. If you have changed your SCSI host bus 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Chapter 2
Installing Microsoft Windows NT 4.0 Server
13
NOTE
The installation of the new network adapter will not take effect
until you restart the server.
If you want to implement Adapter Teaming (requires 2
Network Adapters), Windows NT 4.0 Service Pack version 6a
or above is required.
If there are errors during the installation, you should verify you
installed the correct driver for your adapter.
HP NetRAID-1M Adapter
1.
Create the HP NetRAID driver for Windows NT diskette using the Navigator
CD provided with your NetRAID card. You may refer to the NetRAID card
manuals or HP Navigator CD for additional details.
2. Open
Control Panel | SCSI Adapters | Drivers
tab.
3. Select
Add
.
4. Click
Have Disk
when given a list of SCSI Adapters drivers then browse the
A: drive to locate the appropriate NetRAID-1M driver (in directory
A:\NETRAID
). Click
OK
to install it.
5. Select the "
Hewlett-Packard NetRAID 1M Adapter
"
, and click
OK
.
6.
In the System Settings Change windows, click
Yes
to restart Windows NT.
NOTE
If you do not restart the system at this point, the HP NetRAID-
1M Adapter driver will not be present in the driver list until the
next system boot.
Troubleshooting
This section will help you resolve some of the most common installation
problems.
Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration
The boot manager for Windows NT contains recovery logic to allow you to return
to the last known good configuration. If you have changed your SCSI host bus