HP rp5400 Carrier Grade Addendum - rp5400 Series of Servers - Page 24

Install the Slider Assembly, E-Series Cabinet

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installation Installing the Server in a Rack Install the Slider Assembly The following steps describe how to install the slide-tray assembly into an approved HP equipment enclosure. The slide-tray assembly can be installed into an HP E-Series enclosure and some other approved HP enclosures. NOTE If compliance with Belcore GR63 CORE earthquake standards is required, the enclosure used should be NEBS compliant. Perform this procedure to preparation for field integration of a slide-tray mountable server in an approved enclosure. To prepare an equipment enclosure for field integration of a server proceed as follows: Step 1. Determine whether or not the enclosure into which you will install the slide/tray kit is a E-Series or an approved non-E-Series enclosure. The non-E-Series enclosure has full return flanges on the vertical mounting rails where the E-Series enclosure has only partial return flanges on the vertical mounting rails. Support Notches for Rails Front (Rear) of Cabinet U=44.45 U=44.45 15.875 15.875 12.7 15.875 15.875 12.7 Measurements in mm. Every Fifth Rail Hole Notched 2U Envelope E IA S paced M ounting H oles Non E-series Cabinet Threaded inserts One EIA unit or "U" E-Series Cabinet Step 2. Determine into which vertical, rectangular, slots in the return flanges that the slide/tray kit will be installed. To correctly position the slide tray assembly, count down eight rectangular slots from the top of the enclosure or from the bottom of the equipment installed above. 12 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Chapter 1
Installation
Installing the Server in a Rack
12
Install the Slider Assembly
The following steps describe how to install the slide-tray assembly into an approved HP equipment
enclosure. The slide-tray assembly can be installed into an HP E-Series enclosure and some other approved
HP enclosures.
NOTE
If compliance with Belcore GR63 CORE earthquake standards is required, the enclosure
used should be NEBS compliant.
Perform this procedure to preparation for field integration of a slide-tray mountable server in an approved
enclosure. To prepare an equipment enclosure for field integration of a server proceed as follows:
Step 1.
Determine whether or not the enclosure into which you will install the slide/tray kit is a E-Series
or an approved non-E-Series enclosure.
The non-E-Series enclosure has full return flanges on the vertical mounting rails where the
E-Series enclosure has only partial return flanges on the vertical mounting rails.
Step 2.
Determine into which vertical, rectangular, slots in the return flanges that the slide/tray kit will
be installed. To correctly position the slide tray assembly, count down eight rectangular slots
from the top of the enclosure or from the bottom of the equipment installed above.
15.875
15.875
12.7
15.875
15.875
12.7
Measurements
in mm.
U=44.45
U=44.45
2U Envelope
Support Notches
for Rails
Front (Rear)
of Cabinet
Every Fifth Rail
Hole Notched
EIA Spaced
M ounting Holes
One
EIA unit
or “U”
Threaded inserts
E-Series Cabinet
Non E-series Cabinet