HP rp5400 Carrier Grade Addendum - rp5400 Series of Servers - Page 38

Install the front Bezel.,

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Installation Connecting the Server to DC Power Source Install the front Bezel. NOTE The following procedure is for the installation of the two piece bezel. For information on installing the one piece bezel, refer to the rp5400 Series of Servers One Piece Bezel Installation Instructions located at http://docs.hp.com. 1. Swing the Disk Media access door open so that the plastic pins that go into the metal clips on the Disk Media bay are exposed. CAUTION The plastic pins holding the bezel on the right side are inserted into metal clips on the Disk Media bay. DO NOT bend the plastic pins or they will break off. 2. Holding the bezel with both hands, align the bezel pins with the metal clips on the Disk Media bay and carefully slide the bezel pins into the clips. 3. Attach the left side of the bezel to the server chassis by aligning the bezel pins (item 1) with the chassis clips (item 2) and press the bezel into the chassis until the pins snap into the clips. The illustration below shows the front bezel with locations of bezel pins and chassis clips. 4. Swing the Disk Media access door closed and attach to the right side of the server chassis. 5. Secure the bezel by wrapping the bezel strap around the bezel to prevent the bezel doors from opening. Make sure the bezel strap pull tab is visible. Figure 1-12 Installing the Front Bezel 26 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Chapter 1
Installation
Connecting the Server to DC Power Source
26
Install the front Bezel.
NOTE
The following procedure is for the installation of the two piece bezel. For information on
installing the one piece bezel, refer to the rp5400 Series of Servers One Piece Bezel
Installation Instructions located at http://docs.hp.com.
1.
Swing the Disk Media access door open so that the plastic pins that go into the metal clips on the Disk
Media bay are exposed.
CAUTION
The plastic pins holding the bezel on the right side are inserted into metal clips on the Disk
Media bay. DO NOT bend the plastic pins or they will break off.
2.
Holding the bezel with both hands, align the bezel pins with the metal clips on the Disk Media bay and
carefully slide the bezel pins into the clips.
3.
Attach the left side of the bezel to the server chassis by aligning the bezel pins (item 1) with the chassis
clips (item 2) and press the bezel into the chassis until the pins snap into the clips.
The illustration below shows the front bezel with locations of bezel pins and chassis clips.
4.
Swing the Disk Media access door closed and attach to the right side of the server chassis.
5.
Secure the bezel by wrapping the bezel strap around the bezel to prevent the bezel doors from opening.
Make sure the bezel strap pull tab is visible.
Figure 1-12
Installing the Front Bezel