HP rp5800 Hardware Reference Guide HP rp5800 - Page 53

Installing a 3.5-inch Secondary Hard Drive into a Drive Bay, CAUTION, - hard drive screws

Get HP rp5800 PDF manuals and user guides View all HP rp5800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Installing a 3.5-inch Secondary Hard Drive into a Drive Bay The 3.5-inch secondary hard drive bay is located underneath the 5.25-inch optical drive. To install a secondary hard drive: 1. Follow the procedure in Removing a 5.25-inch Optical Drive from a Drive Bay on page 40 to remove the 5.25-inch optical drive and access the 3.5-inch secondary hard drive bay. CAUTION: Ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet before proceeding. 2. Install four 6-32 standard guide screws in the holes on each side of the drive. HP has provided four extra 6-32 standard guide screws on the front of the chassis, under the front bezel. The 6-32 standard guide screws are silver. Refer to Installing and Removing Drives on page 37 for an illustration of the extra 6-32 standard guide screws location. NOTE: When replacing the drive, transfer the four 6-32 standard guide screws from the old drive to the new one. Figure 2-53 Installing Secondary Hard Drive Guide Screws 3. Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it locks into place. Figure 2-54 Installing a Secondary Hard Drive ENWW Installing and Removing Drives 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Installing a 3.5-inch Secondary Hard Drive into a Drive Bay
The 3.5-inch secondary hard drive bay is located underneath the 5.25-inch optical drive. To install a
secondary hard drive:
1.
Follow the procedure in
Removing a 5.25-inch Optical Drive from a Drive Bay
on page
40
to
remove the 5.25-inch optical drive and access the 3.5-inch secondary hard drive bay.
CAUTION:
Ensure that the computer is turned off and that the power cord is disconnected
from the electrical outlet before proceeding.
2.
Install four 6-32 standard guide screws in the holes on each side of the drive. HP has provided
four extra 6-32 standard guide screws on the front of the chassis, under the front bezel. The
6-32 standard guide screws are silver. Refer to
Installing and Removing Drives
on page
37
for
an illustration of the extra 6-32 standard guide screws location.
NOTE:
When replacing the drive, transfer the four 6-32 standard guide screws from the old
drive to the new one.
Figure 2-53
Installing Secondary Hard Drive Guide Screws
3.
Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive
toward the front of the computer until it locks into place.
Figure 2-54
Installing a Secondary Hard Drive
ENWW
Installing and Removing Drives
47