HP rp7440 Installation Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 65

Accessing the Management Processor via a Web Browser, Con the MP LAN. Refer

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

10. A screen similar to the following is displayed, allowing verification of the settings: Figure 2-32 The ls Command Screen 11. To return to the MP main menu, enter ma. 12. To exit the MP, enter x at the MP main menu. Accessing the Management Processor via a Web Browser Web browser access is an embedded feature of the MP/SCSI card. The Web browser enables access to the server through the LAN port on the core I/O card. MP configuration must be done from an ASCII console connected to the Local RS232 port.. NOTE: The MP/SCSI card has a separate LAN port from the system LAN port. It requires a separate LAN drop, IP address, and networking information from that of the port used by HP-UX. Before starting this procedure, the following information is required: • IP address for the MP LAN • Subnet mask • Gateway address • Host name (this is used when messages are logged or printed) To configure the LAN port for a Web browser, perform the following steps: 1. Connect to the MP using a serial connection. 2. Configure the MP LAN. Refer to "Configuring LAN Information for the MP". 3. Type CMto enter the Command Menu. 4. Type SA at the MP:CM> prompt to display and set MP remote access. Cabling and Power Up 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
10.
A screen similar to the following is displayed, allowing verification of the settings:
Figure 2-32
The ls Command Screen
11.
To return to the MP main menu, enter
ma
.
12.
To exit the MP, enter
x
at the MP main menu.
Accessing the Management Processor via a Web Browser
Web browser access is an embedded feature of the MP/SCSI card. The Web browser enables
access to the server through the LAN port on the core I/O card. MP configuration must be done
from an ASCII console connected to the Local RS232 port..
NOTE:
The MP/SCSI card has a separate LAN port from the system LAN port. It requires a
separate LAN drop, IP address, and networking information from that of the port used by HP-UX.
Before starting this procedure, the following information is required:
•
IP address for the MP LAN
•
Subnet mask
•
Gateway address
•
Host name (this is used when messages are logged or printed)
To configure the LAN port for a Web browser, perform the following steps:
1.
Connect to the MP using a serial connection.
2.
Configure the MP LAN. Refer to
“Configuring LAN Information for the MP”
.
3.
Type
CM
to enter the Command Menu.
4.
Type
SA
at the MP:CM> prompt to display and set MP remote access.
Cabling and Power Up
65