Husqvarna AUTOMOWER 115H 4G Owner Manual - Page 15

To examine where to put the power supply, To make an island on,

Get Husqvarna AUTOMOWER 115H 4G PDF manuals and user guides View all Husqvarna AUTOMOWER 115H 4G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

• Put the charging station in an area with protection from the sun. • If the charging station is installed on an island, make sure to connect the guide wire to the island. Refer to To make an island on page 17. 3.3.3 To examine where to put the boundary wire The boundary wire should be put as a loop around the work area. Sensors in the product senses when the product approaches the boundary wire, and the product selects another direction. CAUTION: If the work area is adjacent to water bodies, slopes, precipices or a public road, the boundary wire must have a protective wall. The wall must be minimum 15 cm / 6 in. in height. 3.3.2 To examine where to put the power supply • Put the power supply in an area with a roof and protection from the sun and rain. • Put the power supply in an area with good airflow. • Use a residual-current device (RCD) when you connect the power supply to the power outlet. WARNING: Do not change the power supply. Do not cut or extend the lowvoltage cable. There is a risk of electrical shock. To make the connection easier between the guide wire and the boundary wire, it is recommended to make an eyelet where the guide wire will be connected. Make the eyelet with approximately 20 cm / 8 in. of the boundary wire. Low-voltage cables of different lengths are available as accessories. CAUTION: Make sure that the blades on the product do not cut the lowvoltage cable. Note: Make a blueprint of the work area before you install the boundary wire and guide wire. CAUTION: Do not put the low-voltage cable in a coil or below the charging station plate. The coil causes interference with the signal from the charging station. 982 - 003 - Installation - 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
•
Put the charging station in an area with
protection from the sun.
•
If the charging station is installed on an
island, make sure to connect the guide wire
to the island. Refer to
To make an island on
page 17
.
3.3.2 To examine where to put the power
supply
•
Put the power supply in an area with a roof
and protection from the sun and rain.
•
Put the power supply in an area with good
airflow.
•
Use a residual-current device (RCD) when
you connect the power supply to the power
outlet.
WARNING:
Do not change the power
supply. Do not cut or extend the low-
voltage cable. There is a risk of
electrical shock.
Low-voltage cables of different lengths are
available as accessories.
CAUTION:
Make sure that the blades
on the product do not cut the low-
voltage cable.
CAUTION:
Do not put the low-voltage
cable in a coil or below the charging
station plate. The coil causes
interference with the signal from the
charging station.
3.3.3 To examine where to put the
boundary wire
The boundary wire should be put as a loop
around the work area. Sensors in the product
senses when the product approaches the
boundary wire, and the product selects another
direction.
CAUTION:
If the work area is adjacent
to water bodies, slopes, precipices or a
public road, the boundary wire must
have a protective wall. The wall must
be minimum 15 cm / 6 in. in height.
To make the connection easier between the
guide wire and the boundary wire, it is
recommended to make an eyelet where the guide
wire will be connected. Make the eyelet with
approximately 20 cm / 8 in. of the boundary wire.
Note:
Make a blueprint of the work area before
you install the boundary wire and guide wire.
982 - 003 -
Installation -
15