Husqvarna AUTOMOWER 115H 4G Owner Manual - Page 39

Indicator lamp in the charging station, To install the guide

Get Husqvarna AUTOMOWER 115H 4G PDF manuals and user guides View all Husqvarna AUTOMOWER 115H 4G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

6.4 Indicator lamp in the charging station For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing green light. If something else appears, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, please contact Husqvarna customer service. Light Cause Action Solid green light Green flashing light Good signals No action required The signals are good and ECO mode is No action required. For more informa- activated. tion on ECO mode. Refer to ECO mode on page 25. Blue flashing light The boundary loop is not connected to the charging station. Check that the boundary wire connectors are fitted properly to the charging station. Refer to To install the guide wire on page 19. Break in the boundary loop. Find out where the break is. Replace the damaged section of the loop with a new loop wire and splice using an original coupler. Yellow flashing light The guide wire is not connected to the charging station. Check that the guide wire connector is properly connected to the charging station. Refer to To install the guide wire on page 19 Red flashing light Break in the guide wire. Find out where the break is. Replace the damaged section of the guide wire with a new loop wire and splice using an original coupler. Interruption in the charging station's an- Contact Husqvarna customer service. tenna. Solid red light Fault in the circuit board or incorrect power supply in the charging station. The fault should be rectified by an authorized service technician. Contact Husqvarna customer service. 982 - 003 - Troubleshooting - 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
6.4 Indicator lamp in the charging
station
For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing
green light. If something else appears, follow the troubleshooting guide below.
There is more help on www.husqvarna.com. If you still need help, please contact Husqvarna customer
service.
Light
Cause
Action
Solid green light
Good signals
No action required
Green flashing
light
The signals are good and
ECO mode
is
activated.
No action required. For more informa-
tion on
ECO mode
. Refer to
ECO mode
on page 25
.
Blue flashing light
The boundary loop is not connected to
the charging station.
Check that the boundary wire connec-
tors are fitted properly to the charging
station. Refer to
To install the guide
wire on page 19
.
Break in the boundary loop.
Find out where the break is. Replace
the damaged section of the loop with a
new loop wire and splice using an origi-
nal coupler.
Yellow flashing
light
The guide wire is not connected to the
charging station.
Check that the guide wire connector is
properly connected to the charging sta-
tion. Refer to
To install the guide wire
on page 19
Break in the guide wire.
Find out where the break is. Replace
the damaged section of the guide wire
with a new loop wire and splice using
an original coupler.
Red flashing light
Interruption in the charging station’s an-
tenna.
Contact Husqvarna customer service.
Solid red light
Fault in the circuit board or incorrect
power supply in the charging station.
The fault should be rectified by an au-
thorized service technician.
Contact Husqvarna customer service.
982 - 003 -
Troubleshooting -
39