IBM 43635gu User Guide - Page 56

into the chassis until it locks into place

Get IBM 43635gu - Servers System X3200 Xeon 2.13ghz PDF manuals and user guides
UPC - 883436002950
View all IBM 43635gu manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

ServeRAID-8s single-drop cable 7. Replace the front system fan assembly. a. Insert the fan assembly retaining tab over the right edge of the hard disk drive backplane; then, rotate the fan assembly toward the backplane. Do not fully close the fan assembly. b. Route the single-drop signal cable through one of the slots on the edge of the fan assembly; then, route the hard disk drive power drop cable through the other slot on the edge of the fan assembly. Ensure that the cables will not be pinched between the fan assembly and the hard disk drive backplane when the fan assembly is installed. c. Rotate the fan assembly toward the backplane until the release tabs are fully engaged. d. Rotate the drive cage back into the server until it stops; then, press and hold the retaining tab on top of the drive cage while rotating the drive cage into the chassis until it locks into place. 8. Reconnect the fan assembly cable to the system board. Note: Before you continue, check all internal power cables to make sure that they are connected to the system board and other optional devices. 9. Install the side cover (see "Reinstalling the side cover" on page 49). 10. Lock the side cover. 11. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. 42 System x3200 Types 4362 and 4363: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
ServeRAID-8s
single-drop cable
7.
Replace the front system fan assembly.
a.
Insert the fan assembly retaining tab over the right edge of the hard disk
drive backplane; then, rotate the fan assembly toward the backplane. Do
not fully close the fan assembly.
b.
Route the single-drop signal cable through one of the slots on the edge of
the fan assembly; then, route the hard disk drive power drop cable through
the other slot on the edge of the fan assembly. Ensure that the cables will
not be pinched between the fan assembly and the hard disk drive
backplane when the fan assembly is installed.
c.
Rotate the fan assembly toward the backplane until the release tabs are
fully engaged.
d.
Rotate the drive cage back into the server until it stops; then, press and
hold the retaining tab on top of the drive cage while rotating the drive cage
into the chassis until it locks into place.
8.
Reconnect the fan assembly cable to the system board.
Note:
Before you continue, check all internal power cables to make sure that
they are connected to the system board and other optional devices.
9.
Install the side cover (see “Reinstalling the side cover” on page 49).
10.
Lock the side cover.
11.
Reconnect the external cables and power cords; then, turn on the attached
devices and turn on the server.
42
System x3200 Types 4362 and 4363: User’s Guide