IBM 43635gu User Guide - Page 63

Reinstalling the side cover

Get IBM 43635gu - Servers System X3200 Xeon 2.13ghz PDF manuals and user guides
UPC - 883436002950
View all IBM 43635gu manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Reinstalling the side cover If you removed the bezel, reinstall it before you reinstall the side cover. See "Reinstalling the two-piece bezel" on page 47. Note: The rear adapter-retention bracket rests against the server side cover. You might find it easier to lay the server on its side to replace the side cover. Cover-release latch Key lock To reinstall the side cover, complete the following steps: 1. Before you install the side cover, make sure that all cables, adapters, and other components are installed and seated correctly and that you have not left loose tools or parts inside the server. Also, make sure that all internal cables are correctly routed. Note: The cover-release latch must be in the unlocked (opened) position before you install the side cover. 2. Insert the tabs inside the cover into the slots on the server chassis. Note: Make sure that each tab on the side cover is in its corresponding slot you close the cover-release latch. 3. Close the cover-release latch to secure the side cover in place. 4. Lock the side cover. Chapter 2. Installing optional devices 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Reinstalling the side cover
If you removed the bezel, reinstall it before you reinstall the side cover. See
“Reinstalling the two-piece bezel” on page 47.
Note:
The rear adapter-retention bracket rests against the server side cover. You
might find it easier to lay the server on its side to replace the side cover.
Cover-release
latch
Key lock
To reinstall the side cover, complete the following steps:
1.
Before you install the side cover, make sure that all cables, adapters, and other
components are installed and seated correctly and that you have not left loose
tools or parts inside the server. Also, make sure that all internal cables are
correctly routed.
Note:
The cover-release latch must be in the unlocked (opened) position before
you install the side cover.
2.
Insert the tabs inside the cover into the slots on the server chassis.
Note:
Make sure that each tab on the side cover is in its corresponding slot
you close the cover-release latch.
3.
Close the cover-release latch to secure the side cover in place.
4.
Lock the side cover.
Chapter 2. Installing optional devices
49