Intel MFS5520VI User Guide - Page 33

Caution, IMPORTANT, Removing the Heatsink

Get Intel MFS5520VI - Multi-Flex Server Compute Module PDF manuals and user guides
UPC - 735858209250
View all Intel MFS5520VI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Removing the Heatsink Caution: Improper removal can damage the heatsink. Pay close attention to the steps and perform each step exactly as indicated to avoid damage. Note: This procedure assumes that you are removing the heatsink for the first time. Note: If you are installing only a single processor on your server board, do not remove the heatsink and spacer over the second processor. 5. Loosen the four captive screws on the heatsink corners in a diagonal manner according to the numbers shown in Figure 9 as follows: a. Starting with the screw at location 1, loosen it by giving it two rotations in the anticlockwise direction (see letter "A" in Figure 9) and stop. (IMPORTANT: Do not fully loosen.) b. Proceed to the screw at location 2 and loosen it by giving it two rotations and stop. c. Loosen screws at locations 3 and 4 by giving each screw two rotations and then stop. d. Repeat steps 5a through 5c by giving each screw two rotations each time until all screws are loosened. 6. Lift the heatsink from the board (see letter "B" in Figure 9). 7. Remove and discard the spacer (see letter "C" in Figure 9). Note: The system is shipped with a spacer installed between the heatsink and the processor socket to protect the socket protective cover. This spacer will need to be removed and discarded before installing the processor. B 3 A 2 1 TIM Discard to Install CPU 4 This Side Up C Discard to Install CPU This Side Up AF003161 Figure 9. Removing the Heatsink Intel® Compute Module MFS5520VI User Guide 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Intel
®
Compute Module MFS5520VI User Guide
19
Removing the Heatsink
Caution:
Improper removal can damage the heatsink. Pay close attention to the steps and perform
each step exactly as indicated to avoid damage.
Note:
This procedure assumes that you are removing the heatsink for the first time.
Note:
If you are installing only a single processor on your server board, do not remove the
heatsink and spacer over the second processor.
5.
Loosen the four captive screws on the heatsink corners in a diagonal manner
according to the numbers shown in
Figure 9
as follows:
a.
Starting with the screw at location 1, loosen it by giving it two rotations in the
anticlockwise direction (see letter “A” in
Figure 9
) and stop. (
IMPORTANT:
Do not fully loosen.
)
b.
Proceed to the screw at location 2 and loosen it by giving it two rotations and
stop.
c.
Loosen screws at locations 3 and 4 by giving each screw two rotations and then
stop.
d.
Repeat steps 5a through 5c by giving each screw two rotations each time until
all screws are loosened.
6.
Lift the heatsink from the board (see letter “B” in
Figure 9
).
7.
Remove and discard the spacer (see letter “C” in
Figure 9
).
Note:
The system is shipped with a spacer installed between the heatsink and the processor
socket to protect the socket protective cover. This spacer will need to be removed and
discarded before installing the processor.
Figure 9.
Removing the Heatsink
A
B
TIM
This Side Up
Discard to Install CPU
This Side Up
Discard to Install CPU
2
3
1
4
C
AF003161