JVC GR D270 Instructions - Page 17

Loading/Unloading A Memory Card, NOTES, ATTENTION - battery

Get JVC GR D270 - Camcorder - 25 x Optical Zoom PDF manuals and user guides View all JVC GR D270 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

● When the battery pack's charge is low, you may not be able to close the cassette holder cover. Do not apply force. Replace the battery pack with a fully charged one or use AC power before continuing. 3 Close the cassette holder cover firmly until it locks into place. To protect valuable recordings Slide the erase protection tab on the back of the tape in the direction of "SAVE". This prevents the tape from being recorded over. To record on this tape, slide the tab back to "REC" before loading it. NOTES: ● If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the cassette holder still does not open, turn the camcorder off then on again. ● If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later, insert it again. ● When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cassette holder cover. GETTING STARTED EN 17 Loading/Unloading A Memory Card Card Cover (MEMORY CARD) Label Memory card (optional) Write/erase protection tab Clipped edge 1 Make sure the camcorder's power is off. 2 Open the card cover (MEMORY CARD). 3 To load a memory card, firmly insert it with its clipped edge first. To unload a memory card, push it once. After the memory card comes out of the camcorder, pull it out. ● Do not touch the terminal on the reverse side of the label. 4 Close the card cover. To protect valuable files (available only for SD Memory Card) Slide the write/erase protection tab on the side of the memory card in the direction of "LOCK". This prevents the memory card from being recorded over. To record on this memory card, slide the tab back to the position opposite to "LOCK" before loading it. NOTES: ● Some brands of memory cards are not compatible with this camcorder. Before purchasing a memory card, consult its manufacturer or dealer. ● Before using a new memory card, it is necessary to format the card. (੬ pg. 30) ATTENTION: Do not insert or remove the memory card while the camcorder is turned on, as this may cause the memory card to be corrupted or cause the camcorder to become unable to recognise whether or not the card is installed. GETTING STARTED

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
EN
17
GETTING STARTED
GETTING STARTED
●
When the battery pack’s charge is low, you may
not be able to close the cassette holder cover. Do
not apply force. Replace the battery pack with a
fully charged one or use AC power before
continuing.
3
Close the cassette holder cover firmly until it
locks into place.
To protect valuable recordings
Slide the erase protection tab on the back of the
tape in the direction of “SAVE”. This prevents the
tape from being recorded over. To record on this
tape, slide the tab back to “REC” before loading
it.
NOTES:
●
If you wait a few seconds and the cassette holder
does not open, close the cassette holder cover
and try again. If the cassette holder still does not
open, turn the camcorder off then on again.
●
If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
●
When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
1
Make sure the camcorder’s power is off.
2
Open the card cover (MEMORY CARD).
3
To load a memory card
, firmly insert it with
its clipped edge first.
To unload a memory card
, push it once. After
the memory card comes out of the camcorder,
pull it out.
●
Do not touch the terminal on the reverse side of
the label.
4
Close the card cover.
To protect valuable files (available only for
SD Memory Card)
Slide the write/erase protection tab on the side
of the memory card in the direction of “LOCK”.
This prevents the memory card from being
recorded over. To record on this memory card,
slide the tab back to the position opposite to
“LOCK” before loading it.
NOTES:
●
Some brands of memory cards are not compatible
with this camcorder. Before purchasing a memory
card, consult its manufacturer or dealer.
●
Before using a new memory card, it is necessary
to format the card. (
±
pg. 30)
ATTENTION:
Do not insert or remove the memory card while the
camcorder is turned on, as this may cause the
memory card to be corrupted or cause the
camcorder to become unable to recognise whether
or not the card is installed.
Loading/Unloading A Memory
Card
Memory card
(optional)
Card Cover (MEMORY CARD)
Label
Write/erase protection tab
Clipped edge