Kenwood KDC-X496 User Manual - Page 41

Troubleshooting guide The messages shown below indicates your system condition. "TOC Error" • The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. • The disc is unreadable. "IN" (blink) • The CD player section is not operating properly. ➪➪ Reinsert the CD. If the CD cannot be ejected or the display continues to blink even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. "Protect" (blink) • The speaker wire has short-circuited or touched the chassis of the vehicle, and then the protection function has been activated. ➪➪ Lay or insulate the speaker cable properly and press the Reset button. If "Protect" does not disappear, consult your nearest service center. "NA File" • An Audio file is played in a format that is not supported by this unit. "Copy PRO" • A copy-protected file is played. "Read Error" • The file system of the connected USB device is broken. ➪➪ Copy the files and folders for the USB device again. If "Read Error" is still displayed, initialize the USB device or use another USB device. "No Device" • A USB device is selected as a source although no USB device is connected. ➪➪ Change the source to any source other than the USB device. Connect an USB device, and change the source to the USB device again. "N/A Device" • An unsupported USB device is connected. • Connection to the iPod has failed. ➪➪ Check that the connected iPod is supported. See (page 76) for information on supported iPods. "No Music Data" • The connected USB device contains no playable audio file. • A medium that does not have playable data has been played. "iPod Error" • Connection to the iPod has failed. ➪➪ Remove the USB device and then reconnect it. ➪➪ Reset iPod/ iPhone. "No Number" • The calling party does not notify a caller ID. • There is no phone number data. "No Data" • There is no outgoing call list. • There is no incoming call list. • There is no missed call list. • There is no phone book list. "No Entry" • The cell-phone has not been registered (pairing). "HF Disconnect" • The unit cannot communicate with the cell-phone. "AUD Disconnect" • The unit cannot communicate with the Bluetooth audio player. "HF Error 07" • The memory cannot be accessed. ➪➪ Cycle the power switch. If this message still appears, press the Reset button on the control unit. "HF Error 68" • The unit cannot communicate with the cell-phone. ➪➪ Cycle the power switch. If this message still appears, press the Reset button on the control unit. "HF Error 89" • Update of the firmware has failed. ➪➪ Retry update of the firmware. "Unknown" • The Bluetooth device cannot be detected. "Device Full" • 5 Bluetooth device have already been registered. No more Bluetooth devices is registered. "PIN Code NG" • The PIN code is wrong. "Connect NG" • The unit cannot be connected to the device. "Pairing Failed" • Pairing error. "N/A Voice Tag" • No voice tags are registered in your cell-phone. "No Phonebook" • Data is not contained in the phone book. "No Message" • No short message in In Box. "Send Error" • SMS could not be sent. "Memory Full" • The tag memory of HD Radio tuner and SiriusXM tuner is FULL. "iPod Full" • The iPod memory is FULL. "No TAG Function" • An iPod which does not support the tag memory has been connected. 80 | KDC-X896/ KDC-BT852HD/ KDC-X496/ KDC-452U/ KMR-550U Contents "Pandora Error 01" • Registration in Bookmark has failed. "Pandora Error 02" • Deletion of the station has failed. "Pandora Error 03" • Registration of the station has failed. "Pandora Error 04" • The number of registered stations has reached the upper limit. ➪➪ Retry after deleting an unnecessary station. "Pandora Error 05" • Registration of Thumbs Up/Down has failed. "Pandora Error 06" • Keyword search has failed. "No Station" • There is no receivable station. "No skips remaining" • No more skips are allowed now. ➪➪ Retry after a while. "Check Device" • Any device ready for Pandora internet radio reception is not connected to this unit. "No Support" • The connected Bluetooth device does not support a voice recognition function. "No Active Device" • Any Bluetooth device supporting a voice recognition function is not connected. SiriusXM Advisory Messages "Check Tuner" • A SiriusXM tuner is not connected to this unit. ➪➪ Check that the connected SiriusXM tuner is connected. "Subscription Updated - Press Enter to Continue" • The SiriusXM subscription has been renewed. ➪➪ Pressing the Control knob will clear the error message. "Ch Unavailable" • The currently selected channel is unavailable. "Chan Unsub" • The currently selected channel is not subscribed to. "Incorrect Code" • The entered pass code is incorrect. "Check Antenna" • No antenna is connected to the SiriusXM tuner. ➪➪ Check that an antenna is connected to the SiriusXM tuner. "No Signal" • No SiriusXM radio signal is received. ➪➪ Check that an antenna is connected to the SiriusXM tuner. "Alert Memory Full" • The number of Alert content has reached the upper limit. ➪➪ Retry after deleting unnecessary Alert content. "Song Stored" • The song you attempted to register as Alert content has already been registered. "Artist Stored" • The artist you attempted to register as Alert content has already been registered. "Art/Sng Unavail" • The content currently being received cannot be registered as a content alert item regardless of whether its artist or song name is stored. English | 81