Konica Minolta Kodak i730 User Guide - Page 66

Perform an Ultrasonics calibration. See Calibrating, See

Get Konica Minolta Kodak i730 PDF manuals and user guides View all Konica Minolta Kodak i730 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Messages UDDS calibration failed UDDS calibration succeeded UDDS is not calibrated UDDS multi-feed detected Unable to scan ID# Operator Message 333 The UDDS calibration failed. • Be sure you are using the correct ultrasonics calibration target. See Chapter 3, "Calibrating the scanner". • Clean the sensors and try again. • If the problem persists, call Service. 332 Informational message. The scanner ultrasonics has been successfully calibrated. 21 • Perform an Ultrasonics calibration. See Chapter 3, "Calibrating the scanner" for procedures. 23, 24, 334 A multi-feed document condition has been detected. • Check the host monitor to see if there are any overlapped documents that may need to be rescanned. This condition may be caused by: • Poor document separation causing overlapped documents. • Stickers on the documents. • Wrinkles in the documents • Thick documents with high multi-feed settings. 5 • The previous error condition has not been corrected. For example, there could be a document jam that has not been completely cleared. • Incomplete or conflicting image processing parameters. • See other log entries for the actual condition. 6-10 A-61500 May 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
6-10
A-61500
May 2010
Messages
ID#
Operator Message
UDDS calibration failed
333
The UDDS calibration failed.
•
Be sure you are using the correct ultrasonics calibration target.
See Chapter 3, “Calibrating the scanner”.
• Clean the sensors and try again.
• If the problem persists, call Service.
UDDS calibration succeeded
332
Informational message.
The scanner ultrasonics has been
successfully calibrated.
UDDS is not calibrated
21
•
Perform an Ultrasonics calibration. See Chapter 3, “Calibrating
the scanner” for procedures.
UDDS multi-feed detected
23, 24, 334
A multi-feed document condition has been detected.
• Check the host monitor to see if there are any overlapped
documents that may need to be rescanned.
This condition may be caused by:
• Poor document separation causing overlapped documents.
• Stickers on the documents.
• Wrinkles in the documents
• Thick documents with high multi-feed settings.
Unable to scan
5
• The previous error condition has not been corrected. For
example, there could be a document jam that has not been
completely cleared.
• Incomplete or conflicting image processing parameters.
• See other log entries for the actual condition.