Konica Minolta Kodak i730 User Guide - Page 72

The rear image path has been, Rear calibration succeeded

Get Konica Minolta Kodak i730 PDF manuals and user guides View all Konica Minolta Kodak i730 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Messages Paused waiting for host Please update firmware before scanning Pod door closed Pod door opened Power on self-test completed Power on self-test failed Printer bitmap font in use Rear calibration failed Rear calibration succeeded Refeed document set Requested pages scanned Paused for image processing Transport timeout ID# Operator Message 1, 48 The feeder has stopped and the transport is still running because the scanner's internal image buffer is almost full. Processing will automatically resume after the capture software application has successfully retrieved enough images to allow the scanner to continue. • Be sure your host computer meets the recommended specifications to avoid this condition. 91 The expected production version of operational firmware was not found. The back-up firmware is in use. • Reload the most recent version of operational scanner firmware. 26 Informational message. The pod was closed. 25 Informational message. The pod is not closed completely. 20 Informational message. The scanner has completed its self-tests after power-on. 6 This error could occur during scanner power-up. • Power-down the scanner, then power down the PC. Wait a few seconds and then power the PC back up, then power up the scanner. • If the problem persists, call Service. 281 Informational message. An alternate printer font file was found and is being used instead of the default font. 112 The rear imaging path calibration failed. • Clean the imaging guides. See Chapter 5, Maintenance for procedures. • Try to calibrate the scanner again. Be sure you are using the correct calibration target. See Chapter 3, "Calibrating the Scanner". • If the problem persists, call Service. 113 Informational message. The rear image path has been successfully calibrated. Many ID numbers Documents passed through the transport but no images were created. • Clean document sensors. • Make sure the leading edges of the documents are aligned. See Chapter 3, "Document preparation" for more information. • Check the condition of your feed module and separation roller tires and your pre-separation pad. Clean and replace if necessary. • Refeed these documents and verify that the images have been captured. 337 Informational message. The scanner has completed scanning the requested number of documents. 63 Informational message. Scanner paused. • Slow host PC may not be able to keep up with the scanner. 336 Informational message. The transport was turned off due to inactivity. 6-16 A-61500 May 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
6-16
A-61500
May 2010
Messages
ID#
Operator Message
Paused waiting for host
1, 48
The feeder has stopped and the transport is still running
because the scanner’s internal image buffer is almost full.
Processing will automatically resume after the capture software
application has successfully retrieved enough images to allow
the scanner to continue.
• Be sure your host computer meets the recommended
specifications to avoid this condition.
Please update firmware before
scanning
91
The expected production version of operational firmware was
not found. The back-up firmware is in use.
• Reload the most recent version of operational scanner
firmware.
Pod door closed
26
Informational message.
The pod was closed.
Pod door opened
25
Informational message
. The pod is not closed completely.
Power on self-test completed
20
Informational message.
The scanner has completed its self-tests
after power-on.
Power on self-test failed
6
This error could occur during scanner power-up.
•
Power-down the scanner, then power down the PC. Wait a few
seconds and then power the PC back up, then power up the
scanner.
• If the problem persists, call Service.
Printer bitmap font in use
281
Informational message
. An alternate printer font file was found
and is being used instead of the default font.
Rear calibration failed
112
The rear imaging path calibration failed.
• Clean the imaging guides. See Chapter 5,
Maintenance
for
procedures.
• Try to calibrate the scanner again. Be sure you are using the
correct calibration target. See Chapter 3, “Calibrating the
Scanner”.
• If the problem persists, call Service.
Rear calibration succeeded
113
Informational message.
The rear image path has been
successfully calibrated.
Refeed document set
Many ID
numbers
Documents passed through the transport but no images were
created.
• Clean document sensors.
• Make sure the leading edges of the documents are aligned.
See Chapter 3, “Document preparation” for more information.
• Check the condition of your feed module and separation roller
tires and your pre-separation pad. Clean and replace if
necessary.
•
Refeed these documents and verify that the images have been
captured.
Requested pages scanned
337
Informational message.
The scanner has completed scanning
the requested number of documents.
Paused for image processing
63
Informational message.
Scanner paused.
• Slow host PC may not be able to keep up with the scanner.
Transport timeout
336
Informational message.
The transport was turned off due to
inactivity.