Konica Minolta bizhub PRESS 1250 bizhub PRESS 1250/1250P/1052/PRO 951 User Gui - Page 32

Press [Adjustment Start]., If adjustment is required

Get Konica Minolta bizhub PRESS 1250 PDF manuals and user guides View all Konica Minolta bizhub PRESS 1250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

2 The Workflow of Both Sides Adjust 2.2 8 Press one of the buttons for the points [a] to [d] and enter the adjustment value using either the touch panel keypad or [,] and [+]. % If the misalignment of the print position is in negative direction, enter a positive value. If it is in positive direction, enter a negative value. % Use [+-] to specify the value to be positive or negative. % Press [Clear] to reset the value. 9 Press [Adjustment Start]. % If [Front] or [Back] is pressed before pressing [Adjustment Start], the entered value will be cleared. If adjustment is required, enter the adjustment value for the selected point, then press [Adjustment Start]. % The entered value will be applied to each point of [Back]. 10 Press Start on the control panel. A test chart will be output. 11 Measure the misalignment of the print position on the output chart. Repeat steps 7 to 11 until there is no misalignment between the front and back sides. 2-14 bizhub PRESS 1250/1250P/1052, bizhub PRO 951

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
2-14
bizhub PRESS 1250/1250P/1052, bizhub PRO 951
The Workflow of Both Sides Adjust
2
2.2
8
Press one of the buttons for the points [a] to [d] and enter the adjustment value using either the touch
panel keypad or [
,
] and [
+
].
%
If the misalignment of the print position is in negative direction, enter a positive value. If it is in pos-
itive direction, enter a negative value.
%
Use [+<->-] to specify the value to be positive or negative.
%
Press [Clear] to reset the value.
9
Press [Adjustment Start].
%
If [Front] or [Back] is pressed before pressing [Adjustment Start], the entered value will be cleared.
If adjustment is required, enter the adjustment value for the selected point, then press [Adjustment
Start].
%
The entered value will be applied to each point of [Back].
10
Press
Start
on the
control panel
.
A test chart will be output.
11
Measure the misalignment of the print position on the output chart.
Repeat steps 7 to 11 until there is no misalignment between the front and back sides.