Konica Minolta bizhub PRESS 1250 Watkiss PowerSquare Sheet Feeder User Manual - Page 41

High Pile and Drawer., If turbo mode is enabled turbo mode = 1, the PSF blows air in both stations

Get Konica Minolta bizhub PRESS 1250 PDF manuals and user guides View all Konica Minolta bizhub PRESS 1250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

3) Turbo mode: Enable or disable the Turbo mode. 3 - If the turbo mode is disabled (turbo mode = 0), the PSF blows air on 1 station at a time. So when the feeding changes from the High Pile to the Drawer, the PSF will stop to blow air in the High Pile and will after start to blow air in the Drawer. This change takes time and decrease the productivity. - If turbo mode is enabled (turbo mode = 1), the PSF blows air in both stations (High Pile and Drawer) at the same time. So, there is no loss of time when the feeding changes to feed from the High Pile to the Drawer (or reverse). Note: The turbo mode is useful ONLY when the job is feeding sheets from both station (High Pile and Drawer). If the job is feeding only from one station, the turbo mode is not needed. Operator Manual Initial issue: 05/11 Page 9 - 41 Latest revision: 03/13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Operator Manual
Page 9 - 41
Initial issue: 05/11
Latest revision: 03/13
3
) Turbo mode:
Enable or disable the Turbo mode.
- If the turbo mode is disabled (turbo mode = 0), the PSF blows air on 1 station at
a time.
So when the feeding changes from the High Pile to the Drawer, the PSF will
stop to blow air in the High Pile and will after start to blow air in the Drawer.
This change takes time and decrease the productivity.
- If turbo mode is enabled (turbo mode = 1), the PSF blows air in both stations
(High Pile and Drawer) at the same time.
So, there is no loss of
time when the feeding changes to feed from the High
Pile to the Drawer (or reverse).
Note: The turbo mode is useful ONLY when the job is feeding sheets from both station
(High Pile and Drawer).
If the job is feeding only from one station, the turbo mode is not needed.
3