Konica Minolta bizhub PRESS 1250 Watkiss PowerSquare Sheet Feeder User Manual - Page 50

B. Test via BCR, For the Drawer Station

Get Konica Minolta bizhub PRESS 1250 PDF manuals and user guides View all Konica Minolta bizhub PRESS 1250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

B. Test via BCR : When the barcode reader is in "Test Mode", a red beam is visible on the paper. The reader is scanning to read the barcode printed on the paper. This operation is useful to check that the red beam of the scanner is well located on the barcode printed on the sheet. For the Drawer Station : Put a sheet in the Drawer with the barcode on the rear of the sheet (trail edge) and visible through the cover (face up). Press 3 sec. the small black button located below LEDs of the sensor (barcode reader). The red beam is visible on the sheet. Note: The beam can be actuated via Pref Menu / Barcode / Test mode. Adjust the barcode reader position for an optimal reading of the barcode which means all LEDs (including green one) of the sensor must be ON. Power OFF the beam by pressing the small black button again (optional). For the High Pile Station : The procedure to put the barcode reader is "Test Mode" is the same than for the Drawer. The position of the reader is automatic (done with the setup of the machine). Operator Manual Initial issue: 05/11 Page 9 - 50 Latest revision: 03/13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Operator Manual
Page 9 - 50
Initial issue: 05/11
Latest revision: 03/13
B. Test via BCR
:
When the barcode reader is in
"Test Mode"
, a red beam is visible on the paper.
The reader is scanning to read the barcode printed on the paper.
This operation is useful to check that the red beam of the scanner is well located on the
barcode printed on the sheet.
For the Drawer Station :
Put a sheet in the Drawer with the barcode on the rear of the sheet (trail edge) and visible
through the cover (face up).
Press
3
sec. the small black button located below LEDs of the sensor (barcode reader).
The red beam is visible on the sheet.
Note: The beam can be actuated via Pref Menu / Barcode / Test mode.
Adjust the barcode reader position for an optimal reading of the barcode which means all
LEDs (including green one) of the sensor must be ON.
Power OFF the beam by pressing the small black button again (optional).
For the High Pile Station :
The procedure to put the barcode reader is
"Test Mode"
is the same than for the Drawer.
The position of the reader is automatic (done with the setup of the machine).