LG CR5765GD Owners Manual - Page 33

Voice message, Solution

Get LG CR5765GD PDF manuals and user guides View all LG CR5765GD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

SMART DIAGNOSIS™ Refer to the following table to resolve error messages encountered during Smart Diagnosis. Voice message Solution Robot Cleaner Smart Diagnosis will be started. Please step Clear any object within a 31/4 ft. (1 m)radius around Home away and clear around 1 meter around the home station. Station, and stay back until the diagnosis is complete. Smart Diagnosis can start when it is being charged. Please Move Robot Cleaner to the Home Station to recharge it. dock Robot Cleaner to the home station to charge. No defect found during diagnosis. Diagnosis mode cannot be operated due to a low battery. Try the Smart Diagnosis again after recharging the Please try again after the battery is charged. battery. Please check if the dust bin is installed with the filter. Open the Dust Bin Cover and examine the bin. Charging cannot be done due to a problem in infrared sensor. Run Smart Diagnosis again and, if the same message is announced, contact an LG Electronics service center. Charging cannot be done due to a problem in ultrasonic Run Smart Diagnosis again and, if the same message is sensor. announced, contact an LG Electronics service center. Charging cannot be done due to a problem in the cliff Clean the three Cliff Sensors on the bottom at the front detection sensors on the bottom. Please clean the sensors. of the unit. Please wipe the lower camera sensor on the right bottom Clean the lens of Camera Sensor on the bottom-right. of the Robot Cleaner. Please wipe the obstacle detecting sensor window on the Clean the lens of the Obstacle Sensors on both the left left and right side of the Robot Cleaner. and right hand sides. A problem has been found on the Gyro Sensor. Run Smart Diagnosis again and, if the same message is announced, contact an LG Electronics service center. Please check for dirt on the left wheel. Check for foreign materials on the left wheel. Please check for dirt on the right wheel. Check for foreign materials on the right wheel. A problem has been found on the left wheel sensor. Run Smart Diagnosis again and, if the same message is announced, contact an LG Electronics service center. A problem has been found on the right wheel sensor. Run Smart Diagnosis again and, if the same message is announced, contact an LG Electronics service center. Please check the brushes for obstructions. Check for any foreign material stuck in the Brush. A problem has been found in the suction motor. Run Smart Diagnosis again and, if the same message is announced, contact an LG Electronics service center. A problem has been found in the acceleration sensor. Run Smart Diagnosis again and, if the same message is announced, contact an LG Electronics service center. In order to listen to the Smart Diagnosis result again, please If you need to repeat the diagnosis result, press the press the charging button. To stop, please press the stop Home button, or press button to finish the diagnosis. button. Smart Diagnosis mode will be turned off. Please try Smart Diagnosis again after turning the main power switch off and on from the back of Robot Cleaner. If the problem continues, please contact LG Electronics customer care. Smart Diagnosis mode cannot be operated with mop plate Run Smart Diagnosis again after removing the Mop being attached. Please try again after removing it. Plate. Smart Diagnosis has failed to operate. Please try it again Turn the main power switch OFF and then ON again after turning off and on the main power switch on the back to resume the diagnosis. Do NOT touch the robot or of the Robot Cleaner. disturb its operation until the diagnosis is complete. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
33
SMART DIAGNOSIS™
Refer to the following table to resolve error messages encountered during Smart Diagnosis.
Voice message
Solution
Robot Cleaner Smart Diagnosis will be started. Please step
away and clear around 1 meter around the home station.
Clear any object within a 3
1
/
4
ft.
(1
m
)radius around Home
Station, and stay back until the diagnosis is complete.
Smart Diagnosis can start when it is being charged. Please
dock Robot Cleaner to the home station to charge.
Move Robot Cleaner to the Home Station to recharge it.
No defect found during diagnosis.
Diagnosis mode cannot be operated due to a low battery.
Please try again after the battery is charged.
Try the Smart Diagnosis again after recharging the
battery.
Please check if the dust bin is installed with the filter.
Open the Dust Bin Cover and examine the bin.
Charging cannot be done due to a problem in infrared
sensor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Charging cannot be done due to a problem in ultrasonic
sensor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Charging cannot be done due to a problem in the cliff
detection sensors on the bottom. Please clean the sensors.
Clean the three Cliff Sensors on the bottom at the front
of the unit.
Please wipe the lower camera sensor on the right bottom
of the Robot Cleaner.
Clean the lens of Camera Sensor on the bottom-right.
Please wipe the obstacle detecting sensor window on the
left and right side of the Robot Cleaner.
Clean the lens of the Obstacle Sensors on both the left
and right hand sides.
A problem has been found on the Gyro Sensor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Please check for dirt on the left wheel.
Check for foreign materials on the left wheel.
Please check for dirt on the right wheel.
Check for foreign materials on the right wheel.
A problem has been found on the left wheel sensor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
A problem has been found on the right wheel sensor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Please check the brushes for obstructions.
Check for any foreign material stuck in the Brush.
A problem has been found in the suction motor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
A problem has been found in the acceleration sensor.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
In order to listen to the Smart Diagnosis result again, please
press the charging button. To stop, please press the stop
button.
If you need to repeat the diagnosis result, press the
Home button, or press
button to finish the diagnosis.
Smart Diagnosis mode will be turned off.
Please try Smart Diagnosis again after turning the main
power switch off and on from the back of Robot Cleaner.
If the problem continues, please contact LG Electronics
customer care.
Smart Diagnosis mode cannot be operated with mop plate
being attached. Please try again after removing it.
Run Smart Diagnosis again after removing the Mop
Plate.
Smart Diagnosis has failed to operate. Please try it again
after turning off and on the main power switch on the back
of the Robot Cleaner.
Turn the main power switch OFF and then ON again
to resume the diagnosis. Do NOT touch the robot or
disturb its operation until the diagnosis is complete.