Lenovo M55e User Manual - Page 53

Closing, cover, connecting, cables

Get Lenovo M55e - ThinkCentre - 9645 PDF manuals and user guides
UPC - 883609167608
View all Lenovo M55e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

7. Close the computer cover and connect the power cord. See "Closing the cover and connecting the cables." 8. Restart the computer, leave it on for approximately 10 seconds. Turn off the computer by holding the power switch for approximately 5 seconds. The computer will turn off. 9. Repeat steps 1 through 3 on page 34. 10. Move the Clear CMOS/Recovery jumper back to the standard position (pins 1 and 2). 11. Reinstall the PCI riser assembly if removed. 12. Close the computer cover and connect the power cord. See "Closing the cover and connecting the cables." Closing the cover and connecting the cables After working with options, you need to install any removed parts, close the computer cover, and reconnect cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the Setup Utility program. To close the computer cover and connect cables to your computer: 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer. 2. Make sure that the cables are routed correctly before lowering the drive bay assembly. Important Correctly route all power supply cables to avoid interference with the drive bay assembly. Keep cables clear of the hinges and sides of the computer chassis. 3. Lower the drive bay assembly and make sure that the drive locks are both in the locked position. Otherwise, you cannot close the computer cover. 4. Close the computer cover. Chapter 3. Installing options 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
7.
Close
the
computer
cover
and
connect
the
power
cord.
See
“Closing
the
cover
and
connecting
the
cables.”
8.
Restart
the
computer,
leave
it
on
for
approximately
10
seconds.
Turn
off
the
computer
by
holding
the
power
switch
for
approximately
5
seconds.
The
computer
will
turn
off.
9.
Repeat
steps
1
through
3
on
page
34.
10.
Move
the
Clear
CMOS/Recovery
jumper
back
to
the
standard
position
(pins
1
and
2).
11.
Reinstall
the
PCI
riser
assembly
if
removed.
12.
Close
the
computer
cover
and
connect
the
power
cord.
See
“Closing
the
cover
and
connecting
the
cables.”
Closing
the
cover
and
connecting
the
cables
After
working
with
options,
you
need
to
install
any
removed
parts,
close
the
computer
cover,
and
reconnect
cables,
including
telephone
lines
and
power
cords.
Also,
depending
on
the
option
that
is
installed,
you
might
need
to
confirm
the
updated
information
in
the
Setup
Utility
program.
To
close
the
computer
cover
and
connect
cables
to
your
computer:
1.
Ensure
that
all
components
have
been
reassembled
correctly
and
that
no
tools
or
loose
screws
are
left
inside
your
computer.
2.
Make
sure
that
the
cables
are
routed
correctly
before
lowering
the
drive
bay
assembly.
Important
Correctly
route
all
power
supply
cables
to
avoid
interference
with
the
drive
bay
assembly.
Keep
cables
clear
of
the
hinges
and
sides
of
the
computer
chassis.
3.
Lower
the
drive
bay
assembly
and
make
sure
that
the
drive
locks
are
both
in
the
locked
position.
Otherwise,
you
cannot
close
the
computer
cover.
4.
Close
the
computer
cover.
Chapter
3.
Installing
options
35