Lexmark 12N0009 Setup Guide - Page 77

Verifying the IP settings, Configuring for PullPrinting, Con for TCP/IP

Get Lexmark 12N0009 - C 910n Color LED Printer PDF manuals and user guides
UPC - 734646560092
View all Lexmark 12N0009 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

6 Change the address by pressing Menu to increase or decrease each number. Press Select to move to the next segment. Press Select when you are finished. The message Saved appears briefly. 7 Press Menu until you see Set IP Netmask, and then press Select. 8 Repeat step 6 to set the IP Netmask. 9 Press Menu until you see Set IP Gateway, and then press Select. 10 Repeat step 6 to set the IP Gateway. 11 When you are finished, press Go to return the printer to the Ready state. Verifying the IP settings Note: On Windows computers, click Start Programs Command Prompt. 1 Print another network setup page. Look under the "TCP/IP" heading and make sure the IP address, netmask, and gateway are what you want. See "Printing a network setup page" on page 69 if you need help. 2 Ping the printer and verify that it responds. For example, at a command prompt on a network computer type "ping" followed by the new printer IP address: ping xxx.xxx.xxx.xx If the printer is active on the network, you will receive a reply. Configuring for Pull Printing If your printer has an optional ImageQuick firmware card installed, it can be configured for Pull Printing once an IP address has been assigned. For detailed configuration instructions, refer to the CD that shipped with the ImageQuick card. Configure for TCP/IP 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
71
Configure for TCP/IP
6
Change the address by pressing
Menu
to increase or decrease
each number. Press
Select
to move to the next segment. Press
Select
when you are finished.
The message
Saved
appears briefly.
7
Press
Menu
until you see Set IP Netmask, and then press
Select
.
8
Repeat step 6 to set the IP Netmask.
9
Press
Menu
until you see Set IP Gateway, and then press
Select
.
10
Repeat step 6 to set the IP Gateway.
11
When you are finished, press
Go
to return the printer to the
Ready state.
Verifying the
IP settings
1
Print another network setup page. Look under the “TCP/IP”
heading and make sure the IP address, netmask, and gateway
are what you want.
See “Printing a network setup page” on page 69 if you need
help.
Note:
On Windows computers,
click Start
Programs
Command Prompt.
2
Ping the printer and verify that it responds. For example, at a
command prompt on a network computer type “ping” followed
by the new printer IP address:
ping xxx.xxx.xxx.xx
If the printer is active on the network, you will receive a reply.
Configuring for
Pull Printing
If your printer has an optional ImageQuick firmware card installed, it
can be configured for Pull Printing once an IP address has been
assigned.
For detailed configuration instructions, refer to the CD that shipped
with the ImageQuick card.