Lexmark E320 Service Manual - Page 177

E220/E321/E323, Continue, If the Printer Type under Integrated

Get Lexmark E320 - Printer - B/W PDF manuals and user guides
UPC - 734646511162
View all Lexmark E320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 177 highlights

4500-E220/E321/E323 7. Par S strobe adjustment for the parallel port can be set to four additional settings in addition to the default setting. Pull-up resistors are only enabled indicating parallel mode 1 is not supported. (Parallel mode 2 is supported and can be turned off or on in the configuration mode.) Adjustments may have to be made if an unusually long parallel cable is being used. 8. Network settings for mark history, history mode, Optra Forms™ mode, and meditech mode can be set. - A service error history report (network) can be printed. - Dump NVRAM prints a hex dump of the NVRAM partition and the re-init NVRAM resets the network NVRAM to the factory defaults. Note: When a controller card is changed in a network printer, print the menu and network sheets. (After POR, press Continue.) If the "Printer Type" under "Integrated Network Option Settings" does not match the "Name" under "Appletalk", go into the printer diagnostics mode and reinitialize NVRAM ("Reinit NVRAM"). Verify that the names match after reprinting the network sheet. Diagnostic aids 3-41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
Diagnostic aids
3-41
4500–E220/E321/E323
7.
Par S strobe adjustment for the parallel port can be set to
four additional settings in addition to the default setting.
Pull–up resistors are only enabled indicating parallel mode 1 is
not supported. (Parallel mode 2 is supported and can be turned
off or on in the configuration mode.) Adjustments may have to
be made if an unusually long parallel cable is being used.
8.
Network settings for mark history, history mode, Optra Forms™
mode, and meditech mode can be set.
–
A service error history report (network) can be printed.
–
Dump NVRAM prints a hex dump of the NVRAM partition
and the re–init NVRAM resets the network NVRAM to the
factory defaults.
Note:
When a controller card is changed in a network printer,
print the menu and network sheets. (After POR, press
Continue
.) If the “Printer Type” under “Integrated
Network Option Settings” does not match the “Name”
under “Appletalk”, go into the printer diagnostics mode
and reinitialize NVRAM (“Reinit NVRAM”). Verify that the
names match after reprinting the network sheet.