Marantz SR9600 SR9600 User Guide - Page 26
Hdmi Jack, Connecting Hdmi Devices - manual
View all Marantz SR9600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 26 highlights
ENGLISH HDMI JACK This unit has two HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. Select an input source from the OSD menu system. (See page 44) Notes: • When the HDMI output is connected to a display monitor that does not support HDCP, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP. • There may be no image output if connected to a TV or display that is not compatible with the above format. • Refer to the instruction manual of the TV or display to be connected to the SR9600 for detailed information regarding the HDMI terminal. * HDCP: High-bandwidth Digital Content Protection CONNECTING HDMI DEVICES An HDMI cable (sold separately) is used to connect the HDMI jack on the SR9600 with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack. HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an HDMI-DVI conversion cable or plug. When connecting to a DVI terminal, connect the audio signal separately. Notes: • Some HDMI components can be controlled over the HDMI cable, but this receiver cannot control other components this way. • When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output. • DVI cables come with 24-pin and 29-pin plugs. This receiver supports 24-pin DVI-D cables; 29pin DVI cables cannot connect to it. • 4PNFTPVSDFEFWJDFTTVDIBT%7%QMBZFSTEPOPU TVQQPSU)%.*SFQFBUFSPQFSBUJPOTMJLFUIPTFPG UIF 43 *O TVDI DBTF QJDUVSFT BSF OPU QSPQFSMZQSPKFDUFEPONPOJUPSTTVDIBT57TBOE QSPKFDUPST • When multiple components are connected to this receiver, turn power to unused components off to prevent interference between them. 24 • Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables. • Some DVD-Audio disks disable downmixing. These types of disks are not played back correctly unless the left, center, right and surround left and right speakers, and subwoofer are connected. • If a DVD player that does not support HDMI 1.1 is connected to the SR9600, multi channel PCM playback is not possible even with DVD-Audio disks. • If a DVD player or other device with DVI output is connected to the SR9600, a separate audio cable (i.Link, optical-digital, coaxial digital or analog) is needed for the audio signals. In this case, select the connected audio input as explained in "1-1 FUNC INPUT SETUP". (See page 33) • Multi channel PCM signals and audio signals of 62 kHz or higher that are input from the HDMI jack are not output from the DIGITAL OUT jacks. • Depending on the quiality of the cable used, the HDMI signal may be affected by noise. DVD PLAYER HDMI OUTPUT VIDEO PROJECTOR HDMI INPUT DIGITAL IN (AUDIO) 1 S400 2 3 S400 4 7.1CH IN MAIN IN L SL SBL C L R SL SR SBL SBR C MULTI OUT A B L R SR (AUX 2) L AUDIO R SBR SW PRE OUT SW AUDIO R SPEAKER C ON OFF IN TAPE OUT IN CD-R/MD OUT CD CENTER SURR.BACK /MULTI SPK. /SPK. C LEFT SURR.BACK /MULTI SPK. /SPK. C RIGHT FRONT A LEFT FRONT A RIGHT FRONT B LEFT DVD LD TV DSS VCR-1 VCR-2 / DVD-R MONITOR OUT IN OUT IN OUT 1 2 5 VIDEO 6 MULTI OUT A B S-VIDEO 7 HDMI 8 Ver 1.1 INPUT-1 (DVD) INPUT-2 (DSS) OUTPUT VIDEO Y CB/PB CR/PR OUTPUT-1 INPUT-1 (DVD) INPUT-2 (DSS) INPUT-3 (VCR-1) INPUT-4 (VCR-2 / DVD-R) AM TUNER-1 GND FM(75Ω) AM TUNER-2 GND FM(75Ω) CLASS 2 WIRING FRONT B RIGHT SURR. LEFT SURR. RIGHT COMPONENT OPT VIDEO Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR OUTPUT-2 SWITCHED 1A 120W MAX SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS COAX 1 3 1 3 IR FLASHER RECEIVER IN IN IN MODEL NO. SR9600 UNSWITCHED 1A 120W MAX AC IN DIGITAL OUT USB AUDIO RS232C 2 4 2 4 DC OUT EMITTER OUT OUT RC-5 MULTI RC AC 120V 60HZ AC OUTLETS SATELLITE TUNER HDMI OUTPUT