Marantz SR9600 SR9600 User Guide - Page 27
Advanced Connection, Connecting The Remote Control Jacks
View all Marantz SR9600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
ENGLISH ADVANCED CONNECTION CENTER L R FRONT SURR. SURR. SUB BACK WOOFER DVD-AUDIO PLAYER or SUPER AUDIO CD MULTICHANNEL PLAYER L CENTER R FRONT SURR. SURR. SUB BACK WOOFER RL RL RL RL RL RL POWER AMPLIFIER Subwoofer CONNECTING THE REMOTE CONTROL JACKS 5 VIDEO 6 S-VIDEO IN OUT IN OUT 1 2 MULTI OUT A B 7 HDMI 8 Ver 1.1 INPUT-1 (DVD) INPUT-2 (DSS) OUTPUT VIDEO Y CB/PB CR/PR OUTPUT-1 INPUT-1 (DVD) INPUT-2 (DSS) INPUT-3 (VCR-1) INPUT-4 (VCR-2 / DVD-R) OPT COMPONENT VIDEO COAX DIGITAL OUT USB AUDIO Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR OUTPUT-2 RS232C 1 3 1 3 2 4 2 4 IR FLASHER RECEIVER IN IN IN MODEL NO. SR9600 OUT DC OUT EMITTER OUT RC-5 MULTI RC AM GND FM(75Ω) AM TUNER-2 GND FM(75Ω) FRONT B RIGHT SURR. LEFT CLASS 2 WIRING SURR. RIGHT SWITCHED 1A 120W MAX SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS UNSWITCHED 1A 120W MAX AC IN AC 120V 60HZ AC OUTLETS Front Center Front Left Right Surround Surround Left Right IR RECEIVER RC OUT 2 1 RL RL LR LR LR LR Surround Back Left Surround Back Right DIGITAL IN (AUDIO) 1 S400 2 3 S400 4 7.1CH IN MAIN IN L SL SBL C L R SL SR SBL SBR C MULTI OUT A B L R SR (AUX 2) L AUDIO R SBR SW PRE OUT SW AUDIO R SPEAKER C ON OFF IN TAPE OUT IN CD-R/MD OUT CD CENTER SURR.BACK /MULTI SPK. /SPK. C LEFT SURR.BACK /MULTI SPK. /SPK. C RIGHT FRONT A LEFT FRONT A RIGHT FRONT B LEFT DVD LD TV DSS VCR-1 VCR-2 / DVD-R MONITOR OUT IN OUT IN OUT 1 2 5 VIDEO 6 MULTI OUT A B S-VIDEO 7 HDMI 8 Ver 1.1 INPUT-1 (DVD) INPUT-2 (DSS) OUTPUT VIDEO Y CB/PB CR/PR OUTPUT-1 INPUT-1 (DVD) INPUT-2 (DSS) INPUT-3 (VCR-1) INPUT-4 (VCR-2 / DVD-R) AM TUNER-1 GND FM(75Ω) AM TUNER-2 GND FM(75Ω) CLASS 2 WIRING FRONT B RIGHT SURR. LEFT SURR. RIGHT COMPONENT OPT VIDEO Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR OUTPUT-2 SWITCHED 1A 120W MAX SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS COAX 1 3 1 3 IR FLASHER RECEIVER IN IN IN MODEL NO. SR9600 UNSWITCHED 1A 120W MAX AC IN DIGITAL OUT USB AUDIO RS232C 2 4 2 4 DC OUT EMITTER OUT OUT RC-5 MULTI RC AC 120V 60HZ AC OUTLETS CONNECTING MULTICHANNEL AUDIO SOURCE The 7.1ch input jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD-audio player or external decoder. If you use these jacks, switch on the 7.1ch input and set the 7.1ch input level from the OSD menu system. (see page 33). CONNECTING AN EXTERNAL POWER AMPLIFIER The PRE OUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. REMOTE CONTROL IN OUT CD RECORDER EXTERNAL INTERNAL REMOTE CONTROL IN OUT MD DECK EXTERNAL INTERNAL REMOTE CONTROL IN OUT CD PLAYER EXTERNAL INTERNAL q You can control other Marantz products through the SR9600 with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on the SR9600, then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote control only at the SR9600. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the other units, (not the SR9600) to "EXT."(external) to use this feature. w Whenever external infrared sensors or similar devices are connected to the RC-5 IN jack on the SR9600, be sure to always disable operation of the infrared sensor on the SR9600 by using the following procedure. 1. Hold down the MULTI button and the MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL display. 3. Press the ENTER buttons to change this to "IR=DISABLE". 4. Press the OK/ENTER button for five seconds. The infrared sensor on the main unit is now disabled. Note: • Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the SR9600 will be unable to receive remote control commands. 5. To restore to the original setting, perform steps 1 to 4 and set to "IR=ENABLE". 25