Marantz SR9600 SR9600 User Guide - Page 58

ENGLISH VIDEO ON/OFF DISPLAY MODE When no video signal is connected to the SR9600 You can select the display mode for the front panel or a DVD, etc., is connected directly to your TV, the display on the SR9600. unnecessary video circuit can be turned off by setting the video off mode. 1. To select this mode, press the DISPLAY 1. To set the video off mode, tap the A/V Amp and press the page up button until page 5/8 is displayed. Tap the Video off on the remote control unit. AV SURROUND RECEIVER SR9600 "V-OFF" indicator will be illuminated when this INPUT SELECTOR function is activated. button on the front panel or tap the Display on the remote control. wed Jun 01 4:40pm 1. 5/8 A/V Amp Mode 1. VOLUME wed Jun 01 4:40pm 5/8 A/V Amp Mode 1. STANDBY POWER ON/STANDBY PHONES PURE DIRECT THX DOWN TUNING UP BAND F/P SURROUND MODE AUTO MULTI MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 2. To cancel the Video Off mode, tap the Video off on the remote control unit again. When this button is pressed, the Display mode is switched in the following sequence: Normal mode → Level Meter mode → Auto Display Off mode → Display Off mode → Normal mode → .... Normal mode: Displays the selected component. Level meter mode: Displays the current output level of up to 7.1 channels as a bar graph. MULTI A.B.SPK SPKR A.B PEAK ATT SLEEP V-OFF Re-EQ NIGHT DVD:AT>HDMI.2 HDMI DIGITAL DIGITAL EX LCR S BS LL S L CR W S SB RR dB LFE +18.0 SL S SR Auto Display Off mode: The display is off. But, if you make a change to the unit such as the input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed. Display Off mode: The display is off completely. Note: • Only the "DISP" indicator will be illuminated on the front panel display when the Display Off mode is selected. • Only SBL is displayed in the Level Meter mode if "SURR.B" on the SPEAKER SIZE menu in the SETUP MENU is set to 1 channel (1CH). SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source. 1. Tap the A/V Amp and press the page up button until page 5/8 is displayed. Tap the A/D on the remote control unit. wed Jun 01 4:40pm 5/8 A/V Amp Mode 1. When the A/D is tapped, the input mode is switched in the following sequence: Auto → i.LINK → HDMI → Digital→ Analog → Auto .... Auto mode: The types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. i.LINK mode: i.LINK mode can be selected only when an i.LINK device has been assigned as an input source. HDMI mode: HDMI mode can be selected only when an HDMI input has been assigned as an input source. Digital mode: The input signal is fixed to an assigned digital input terminal. Analog mode: The analog input jacks are selected. This selection is temporary and will not be stored in memory. To store changes to the input mode, select "1. INPUT SETUP" from the MAIN MENU. (See page 32) RECORDING AN ANALOG SOURCE In normal operation, the audio or video source selected for listening through the SR9600 is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD-R/MD OUT, VCR1 OUT, and VCR2/DVD-R OUT in the Record mode. To record the input source signal you are currently watching or listening to 1. Select the input source to record by turning the INPUT SELECTOR knob on the front panel or simply select a source from among the Source Select screen on page 1/8 on the remote control unit. The input source is now selected and you may watch or listen to it as desired. 1. AV SURROUND RECEIVER SR9600 wed Jun 01 4:40pm 1/8 A/V Amp Source Select INPUT SELECTOR VOLUME STANDBY POWER ON/STANDBY PHONES PURE DIRECT THX DOWN TUNING UP BAND F/P SURROUND MODE AUTO PURE DIRECT THX MULTI 1. MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 2. The currently selected input source signal is output to TAPE OUT, CD-R/MD OUT, VCR1 OUT, and VCR2/DVD-R OUT for recording. 3. Start recording to the recording component as desired. 56