Marantz SR9600 SR9600 User Guide - Page 60

ENGLISH BASIC OPERATION (TUNER) This receiver incorporates two tuners with completely independent remote control buttons. Tuner 1 is used in this explanation. (Using the remote control unit) 1. To select the tuner and desired band (AM or FM), tap the AM or FM. 2. Tap and hold the Tuning and for 1 sec or more. 3. Automatic searching begins then stops when a station is tuned in. LISTENING TO THE TUNER The AM frequency scan increments are selectable. The default is 10 kHz increments. If your country's standard is 9 kHz increments, press and hold either the BAND button on the front panel or the AM button on the remote control unit for 5 sec or more. The new scan increments will be stored.AVSURROUNDRECEIVERSR9600 Note: INPUT SELECTOR If tuning does not stop at the desired station, use manual tuning. MANUAL TUNING 2. 1. wed Jun 01 4:40pm 1/2 Tuner 1 Tuner 1 : Main 1. VOLUME • The all Preset memory for the tuner will be cleared clear by changing this setting. PURE DIRECT THX DOWN TUNING UP BAND F/P 2. DOWN UP RROUND RECEIVER SR9600 AUTO TUNING 2. 1. PURE DIRECT THX DOWN TUNING UP BAND F/P DOWN STANDBY POWER ON/STANDBY PHONES 1. VOLUME wed Jun 01 4:40pm 1/2 Tuner 1 Tuner 1 : Main 2. UP PHONES SURROUND MODE AUTO MULTI MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R SURROUND MODE AUTO MULTI MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R (Using the SR9600) 1. To select the tuner and desired band (AM or FM), press the BAND button on the front panel 2. Turn the GYRO TUNING dial on the front panel to select the desired station. DIRECT FREQUENCY CALL (FM) TUNING MODE (AUTO STEREO OR MONO) wed Jun 01 4:40pm 1/2 Tuner 1 Tuner 1 : Main 1. wed Jun 01 4:40pm 2/2 Tuner 1 Tuner 1 : Key/RDS AV SURROUND RECEIVER SR9600 INPUT SELECTOR 3. 2. STANDBY POWER ON/STANDBY PHONES PURE DIRECT THX DOWN TUNING UP BAND F/P SURROUND MODE AUTO MULTI MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC VOLUME DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R wed Jun 01 4:40pm 1/2 Tuner 1 Tuner 1 : Main 1. To select the tuner and desired band (AM or FM), press the page up button on the remote control unit until page 2/2 appears. 2. Tap the Frequency Direct. "FREQ ---" will appear on the display. 3. Input your desired station's frequency with the numeric keypad on the remote control unit. 4. The desired station will automatically be tuned. When in the Auto Stereo mode, "AUTO" indicator is illuminated on the display. The "ST" indicator is illuminated when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the "TUNED" and "ST" indicators are not illuminated. If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the TMODE button on the front panel or tap the Stereo/ Mono on the remote control unit. "AUTO" indicator is illuminated on the display. (Using the SR9600) 1. To select the tuner and desired band (AM or FM), press the BAND button on the front panel. 2. Press the AUTO TUNE button on the front panel, and turn the GYRO TUNING dial to start the Auto Tuning mode. 3. Automatic searching begins then stops when a station is tuned in. (Using the remote control unit) 1. To select the tuner and desired band (AM or FM), tap the AM or FM. 2. Tap the Tuning or . Note: • Reception sensitivity worsens when simultaneously using tuner 1 and 2 in the below cases. In such case, moving the antennas farther apart improves reception. FM: Tuner 1 frequency + 10.7 MHz = Turner 2 frequency Tuner 2 frequency + 10.7 MHz = Turner 1 frequency AM: Tuner 1 frequency + 450 kHz = Turner 2 frequency Tuner 2 frequency + 450 kHz = Turner 1 frequency 58