Maytag MEDE900VJ Use and Care Guide - Page 19

Excessive

Weight

Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1.

To protect

the

floob

use a large

flat

piece

of cardboard

from

the dryer

carton.

Place

cardboard

under

the

entire

back

edge

of the

dryer.

2.

Firmly

grasp

the

body

of the

dryer

(not

the console

panel).

Gent['/[a,/the

dryer

on

the

cardboard.

See illustration.

The dryer must be connected

to the cold water faucet using the new inlet hoses. Do not use

old hoses.

1.

Turn

cold

water

faucet

off

and

remove

washer

inlet

hose.

2.

Remove

old

rubber

washer

from

inlet

hose and

replace

with

new

rubber

washer

provided.

If space

permits,

attach

the brass female

end

of the

"Y"

connector

to the

cold

water

faucet.

NOTE:

If "Y"

connector

can

be attached

direct['/to

cold

water

faucet,

go to Step 6.

If "Y"

connector

cannot

be attached

direct['/to

the cold

water

faucet,

the

short

hose

must be

used. Continue

with

Step 3.

3.

Attach

short

hose to cold

water

faucet.

Screw

on

coupling

by hand

until

it is seated

on

faucet.

4.

Using pliers, tighten the couplings

with

an additional

two-thirds

turn.

3.

Examine

the

leveling

legs.

Find

the diamond

marking.

4.

Screw

the

legs into

the

leg holes

by hand.

Use a wrench

to finish

turning

the

legs until

the

diamond

marking

is no

longer

visible.

5.

Place

a carton

corner

post

from

dryer

packaging

under

each

of the

2 dryer

back

corners.

Stand the

dryer

up.

Slide

the

dryer

on the

corner

posts

until

it is close

to its final

location.

I.eave enough

room

to

connect

the exhaust

vent.

1.

Using

a 4" (1 0.2 cm)

clamp,

connect

vent

to exhaust

outlet

in dryer.

If connecting

to

existing

vent,

make

sure

the vent

is clean.

The dryer

vent

must fit over

the

dryer

exhaust

outlet

and

inside

the exhaust

hood.

Check

that the

vent

is secured

to exhaust

hood

with

a

4" (1 0.2

cm)

clamp.

2.

Move

dryer

into

its final

location.

Do

not

crush

or kink

vent.

3.

Once

the

exhaust

vent

connection

is made,

remove

the corner

posts

and

cardboard.

NOTE:

I)o

not

overtighten.

Damage

to the

coupling

can

result.

5.

Attach

"Y"

connector

to brass male end

of

small

hose. Screw

on coupling

by hand

until

it

is seated

on

connector.

6.

Attach

straight

end

of

long

hose to

"Y"

connector.

7.

Attach

washer

cold

inlet

hose to other

end

of "Y"

connector.

Screw

on coupling

by hand

until

it is seated on

connector.

8.

Using

pliers,

tighten

the

couplings

with

an additional

two-thirds

turn.

9.

A

A. Inlet to cold

water

NOTE:

Do

not

overtighten.

Damage

to the

coupling

can

result.

Attach

angled

end

of

long

hose to fill

valve

at bottom

of dryer

back

panel.

Screw

on

coupling

by hand

until

it is seated

on fill

valve

connector.

iiiiiii ::i

Maytag MEDE900VJ Use and Care Guide - Page 19

i ::i - washer

Page 19 highlights