Maytag MER5775RAB Installation Manual - Page 6

Service, or Conduit, Installation, ACCEPTABLE, INSTALLATION

Get Maytag MER5775RAB - Ceramic Range PDF manuals and user guides View all Maytag MER5775RAB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

CONNECTING THE RANGE FIGURE 6 3-Wire Service Cord or Conduit Installation 1. Insure that the copper ground strap IS CONNECTED between the middle post of the main terminal connection block and the range chassis. 2. If bare copper or aluminum wiring is used, attach adapter lugs as shown in figure 6. (See Bare Wire Connection). Torque specifications are shown below. 3. The middle wire of the service cord or ground lead of 3-wire conduit MUST connect to the neutral (middle) post of the main terminal block. The other two wires of the service cord or conduit connect to the outside posts of the main terminal connection block. Polarity is unimportant. If using bare wire, attach wire to appropriate lug as shown. Torque specifications are shown below. 4. An appropriate strain relief for service cord or conduit MUST be attached to the conduit plate. ACCEPTABLE - 3 WIRE PLUG INSTALLATION CONDUIT PLATE MAIN TERMINAL CONNECTIONBLOCK MIDDLEWIRE OF SERVICECORD OR CONDUIT STRAIN RELIEF RED ADAPTER LUGS LOCAIED IN LITERATUREKIT WHITE 8LACK RARF WIRF TOROUF SPECIFICAIION_ LUG ATTACH[O 10 TERMINAL BLOCK - 2g IN-LB 10-14 8 4-6 20 tg-LU 25 IN-LB 35 Ig-LB FORUSE WITH CONDUIT. REMOVE BRACKET. FLIP RE-ATTACHWITH SMALL ALTERNATIVF INSTALLATION _ ///'-.,I_ ///A\\ \/ /A MOUNTEDFLUSH TO WALL OUTLETRECEPTACLETO BE -_ ROTATEDAS SHOWNIF NOT _ FLUSH TO WALL % Z_/ -,.v FIGURE 6 -6-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
CONNECTING
THE
RANGE
FIGURE
6
3-Wire
Service
Cord
or Conduit
Installation
1.
Insure that the copper ground strap IS CONNECTED
between
the middle post of the main terminal
connection
block and the range chassis.
2.
If bare copper or aluminum
wiring is used, attach
adapter lugs as shown in figure 6. (See Bare Wire
Connection).
Torque specifications
are shown below.
3.
The middle wire of the service cord or ground lead of
3-wire conduit
MUST connect to the neutral (middle)
post of the main terminal block. The other two wires of
the service
cord or conduit connect to the outside
posts of the main terminal connection
block. Polarity is
unimportant.
If using bare wire, attach wire to
appropriate
lug as shown. Torque specifications
are
shown below.
4.
An appropriate
strain relief for service
cord or conduit
MUST be attached to the conduit
plate.
ACCEPTABLE
-
3 WIRE
PLUG
INSTALLATION
CONDUIT
PLATE
MOUNTEDFLUSH
TO
WALL
MAIN
TERMINAL
CONNECTION
BLOCK
MIDDLEWIRE
OF
SERVICECORD
OR CONDUIT
STRAIN
RELIEF
WHITE
ADAPTER
LUGS
LOCAIED
IN
LITERATURE
KIT
8LACK
RARF
WIRF
TOROUF
SPECIFICAIION_
LUG
ATTACH[O
10
TERMINAL BLOCK
-
2g
IN-LB
10-14
20
tg-LU
8
25
IN-LB
4-6
35
Ig-LB
RED
ALTERNATIVF
INSTALLATION
FOR
USE
WITH
CONDUIT.
_
REMOVE BRACKET.
FLIP
///'-.,_
I
RE-ATTACHWITH
SMALL
///A\\
\/
/A
OUTLETRECEPTACLE
TO
BE -_
ROTATEDASSHOWNIF
NOT
_
Z_/
-,.v
FLUSH
TO WALL
%
FIGURE
6
-6-