Maytag MHW9000YG Use & Care Guide - Page 16

Winter Storage Care, Non-use And Vacation Care, Transporting Your Washer, Cleaning The Door Seal

Get Maytag MHW9000YG PDF manuals and user guides View all Maytag MHW9000YG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

CLEANING THE DOOR SEAL 1. Open the washer door and remove any clothing or items from the washer. 2. Inspect the gray colored seal between the door opening and the basket for stained areas. Pull back the seal to inspect all areas under the seal and to check for foreign objects. Seal 3. If stained areas are found, wipe down these areas of the seal, using the procedure that follows. a) Mix a dilute solution, using 3/4 cup (180 mL) of liquid chlorine bleach, and 1 gal. (3.8 L) of warm tap water. b) Wipe the seal area with the dilute solution, using a damp cloth. c) Let stand 5 minutes. d) Wipe down area thoroughly with a dry cloth and let the washer interior air dry with door open. IMPORTANT: Wear rubber gloves when cleaning for prolonged periods. n Refer to the bleach manufacturer's instructions for proper use. NON-USE AND VACATION CARE Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps: 1. Unplug or disconnect power to washer. 2. Turn off water supply to washer to avoid flooding due to water pressure surges. WINTER STORAGE CARE IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer. To winterize washer: 1. Shut off both water faucets, disconnect and drain water inlet hoses. 2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run washer on RINSE/DRAIN AND SPIN cycle for about 30 seconds to mix antifreeze and remaining water. 3. Unplug washer or disconnect power. IMPORTANT: To reduce risk of hose failure, replace inlet hoses every five years and periodically inspect for kinks, cuts, wear or water leaks. HELPFUL TIP: When replacing your inlet hoses, mark replacement date on label with a permanent marker. TRANSPORTING YOUR WASHER 1. Shut off both water faucets. Disconnect and drain water inlet hoses. 2. If washer will be moved during freezing weather, follow WINTER STORAGE CARE directions before moving. 3. Disconnect drain hose from drain system and from back of washer. 4. Unplug power cord. 5. Place inlet hoses and drain hose inside washer basket. 6. Bundle power cord with a rubber band or cable tie to keep it from hanging onto the ground. IMPORTANT: Call for service to install new transport bolts. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid structural damage to your washer, it must be properly set up for relocation by a certified technician. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
16
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1.
Unplug or disconnect power to washer.
2.
Turn off water supply to washer to avoid flooding due
to water pressure surges.
WINTER STORAGE CARE
IMPORTANT:
To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1.
Shut off both water faucets, disconnect and drain water
inlet hoses.
2.
Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE/DRAIN AND SPIN cycle for about 30
seconds to mix antifreeze and remaining water.
3.
Unplug washer or disconnect power.
IMPORTANT:
To reduce risk of hose failure, replace inlet
hoses every five years and periodically inspect for kinks,
cuts, wear or water leaks.
HELPFUL TIP:
When replacing your inlet hoses, mark
replacement date on label with a permanent marker.
NON-USE AND VACATION CARE
TRANSPORTING YOUR WASHER
1.
Shut off both water faucets. Disconnect and drain water
inlet hoses.
2.
If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3.
Disconnect drain hose from drain system and from back
of washer.
4.
Unplug power cord.
5.
Place inlet hoses and drain hose inside washer basket.
6.
Bundle power cord with a rubber band or cable tie to
keep it from hanging onto the ground.
IMPORTANT:
Call for service to install new transport bolts.
Do not reuse transport bolts. Washer must be transported
in the upright position. To avoid structural damage to your
washer, it must be properly set up for relocation
by a certified technician.
CLEANING THE DOOR SEAL
1.
Open the washer door and remove any clothing or items
from the washer.
2.
Inspect the gray colored seal between the door opening
and the basket for stained areas. Pull back the seal to
inspect all areas under the seal and to check for foreign
objects.
3.
If stained areas are found, wipe down these areas of the
seal, using the procedure that follows.
a)
Mix a dilute solution, using 3/4 cup (180 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b)
Wipe the seal area with the dilute solution, using
a damp cloth.
c)
Let stand 5 minutes.
d)
Wipe down area thoroughly with a dry cloth and let the
washer interior air dry with door open.
IMPORTANT:
Wear rubber gloves when cleaning for prolonged periods.
n
Refer to the bleach manufacturer’s instructions for
proper use.
Seal