Netgear DM111PSP DM111PSP User Manual - Page 60

Table 5-1., WAN Setup, The following table describes the settings on the WAN Setup screen. - dm111pspv2 qos

Get Netgear DM111PSP - ADSL2+ Ethernet Modem PDF manuals and user guides View all Netgear DM111PSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

ADSL2+ Modem Router DM111PSPv2 User Manual The following table describes the settings on the WAN Setup screen. Table 5-1. WAN Setup Field Description PVC Name Connect hyperlink VPI/VCI Category Protocol NAT (Net Address Translation) QoS (Quality of Service) WAN IP Address MTU Edit Add button Connection link name. Click the Connect hyperlink to connect to the WAN. The VPI/VCI settings (see Table 5-3 on page 5-4 for an explanation of these settings). UBR (Unspecified Bit Rate), a guaranteed QoS for ATM networks. PPPoE LLC/SNAP (Logical Link Control/Sub Network Access Protocol). NAT automatically assigns private IP addresses (10.1.1.x) to LAN-connected devices. • On. NAT is enabled. • Off. NAT is disabled. Disable NAT only if you are sure that you do not require it. For example, if the modem router is on the same network as a router that is using NAT. The modem router supports QoS applications. See "Quality of Service (QoS) Settings" on page 5-10. The method that the ISP uses to assign the WAN IP address. If your ISP assigns private IP addresses, your private WAN IP address is shown here. Otherwise the setting is Auto assigned. The MTU (Maximum Transmit Unit) value set in the LAN IP screen. See "LAN IP Setup" on page 4-1. Icons that enable you to edit (the pencil icon) or delete (the waste bin icon) the WAN connection. For adding a Permanent Virtual Connection (PVC) to the WAN. See the following section. 5-2 Advanced WAN Configuration v1.0, December 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
ADSL2+ Modem Router DM111PSPv2 User Manual
5-2
Advanced WAN Configuration
v1.0, December 2008
The following table describes the settings on the WAN Setup screen.
Table 5-1.
WAN Setup
Field
Description
PVC Name
Connect
hyperlink
Connection link name.
Click the
Connect
hyperlink to connect to the WAN.
VPI/VCI
The VPI/VCI settings (see
Table 5-3 on page 5-4
for an explanation of these
settings).
Category
UBR (Unspecified Bit Rate), a guaranteed QoS for ATM networks.
Protocol
PPPoE LLC/SNAP (Logical Link Control/Sub Network Access Protocol).
NAT (Net Address
Translation)
NAT automatically assigns private IP addresses (10.1.1.x) to LAN-connected
devices.
•
On
. NAT is enabled.
•
Off
. NAT is disabled. Disable NAT only if you are sure that you do not require
it. For example, if the modem router is on the same network as a router that is
using NAT.
QoS (Quality of Service)
The modem router supports QoS applications. See
“Quality of Service (QoS)
Settings” on page 5-10
.
WAN IP Address
The method that the ISP uses to assign the WAN IP address. If your ISP assigns
private IP addresses, your private WAN IP address is shown here. Otherwise the
setting is Auto assigned.
MTU
The MTU (Maximum Transmit Unit) value set in the LAN IP screen. See
“LAN IP
Setup” on page 4-1
.
Edit
Icons that enable you to edit (the pencil icon) or delete (the waste bin icon) the
WAN connection.
Add
button
For adding a Permanent Virtual Connection (PVC) to the WAN. See the
following section.