Nokia IP290 Installation Guide - Page 61

Before You Begin

Get Nokia IP290 - Security Appliance PDF manuals and user guides View all Nokia IP290 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Replacing a Nokia Encryption Accelerator Card Before You Begin To install the accelerator card, you need: „ Physical access to the appliance „ The Nokia encryption accelerator card and installation kit „ Phillips-head screwdriver „ Four screws (included in kit) „ Grounding wrist strap (included in kit) Caution To help guard against electrostatic discharge damage, make sure you are properly grounded by using a grounding wrist strap and following the instructions provided with the wrist strap before you handle the components or open the appliance. To install the accelerator card 1. Use Nokia Network Voyager or the command-line interface (CLI) to perform an orderly shutdown of the IP290 appliance. For information about how to access Network Voyager and the related reference materials, see "Using Nokia Network Voyager" on page 36. 2. Turn off the power to the IP290 appliance. 3. Remove the power cord. Warning To reduce the risk of fire, electric shock, and injury, disconnect the power cord and any cables that connect to the appliance or gateway before you open the chassis and expose internal components. Even though the power switch is turned off, power is still present inside the appliance or gateway. 4. Loosen the two chassis tray assembly retaining screws. STATUS POWER FAULT IP290 1 3 5 1000BaseT LINK ACT SLOT 1 LINK ACT RESET AUX CONSOLE 2 4 6 00565 Chassis tray assembly retaining screws 5. Slide the chassis tray assembly forward and completely remove the chassis to expose the motherboard components. Nokia IP290 Security Platform Installation Guide 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Replacing a Nokia Encryption Accelerator Card
Nokia IP290 Security Platform Installation Guide
61
Before You Begin
To install the accelerator card, you need:
Physical access to the appliance
The Nokia encryption accelerator card and installation kit
Phillips-head screwdriver
Four screws (included in kit)
Grounding wrist strap (included in kit)
Caution
To help guard against electrostatic discharge damage, make sure you are properly
grounded by using a grounding wrist strap and following the instructions provided with
the wrist strap before you handle the components or open the appliance.
To install the accelerator card
1.
Use Nokia Network Voyager or the command-line interface (CLI) to perform an orderly
shutdown of the IP290 appliance.
For information about how to access Network Voyager and the related reference materials,
see
“Using Nokia Network Voyager”
on page 36.
2.
Turn off the power to the IP290 appliance.
3.
Remove the power cord.
Warning
To reduce the risk of fire, electric shock, and injury, disconnect the power cord and any
cables that connect to the appliance or gateway before you open the chassis and
expose internal components. Even though the power switch is turned off, power is still
present inside the appliance or gateway.
4.
Loosen the two chassis tray assembly retaining screws.
5.
Slide the chassis tray assembly forward and completely remove the chassis to expose the
motherboard components.
IP290
STATUS
SLOT 1
AUX
RESET
1
3
5
2
4
6
CONSOLE
POWER
FAULT
00565
1000BaseT
LINK
ACT
LINK
ACT
Chassis tray assembly retaining screws