Nokia N93 User Guide - Page 108

Packet data

Get Nokia N93 - Smartphone 50 MB PDF manuals and user guides View all Nokia N93 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Tools Security settings for WEP are as follows: Wep key in use-Select the WEP key number. You can create up to four WEP keys. The same settings must be entered on the wireless LAN access point device. Authentication type-Select Open or Shared for the authentication type between your device and the wireless LAN access point device. WEP key settings-Enter WEP encryption (length of the key), WEP key format (ASCII or Hexadecimal), and WEP key (the WEP key data in the selected format). Security settings for 802.1x and WPA/WPA2 are as follows: WPA mode-Select the means of authentication: EAP to use an extensible authentication protocol (EAP) plug-in or Pre-shared key to use a password. Complete the appropriate settings: EAP plug-in settings (only for EAP)-Enter the settings as your service provider instructs. Pre-shared key (only for Pre-shared key)-Enter a password. The same password must be entered on the wireless LAN access point device. TKIP encryption-Select whether Temporal Key Integrity Protocol (TKIP) is used. Homepage-Define a home page. Select Options > Advanced settings and from the following: IPv4 settings: Phone IP address (the IP address of your device), Subnet mask (the subnet IP address), Default gateway (the gateway), and DNS address-Enter the IP addresses of the primary and secondary DNS server. Contact your internet service provider for these addresses. IPv6 settings > DNS address-Select Automatic, Well-known, or User defined. Ad-hoc channel (only for Ad-hoc)-To enter a channel number (1-11) manually, select User defined. Proxy serv. address-Enter the address for the proxy server. Proxy port number-Enter the proxy port number. Packet data The packet data settings affect all access points using a packet data connection. Packet data conn.-If you select When available and you are in a network that supports packet data, the device registers to the packet data network. Starting an active packet data connection (for example, to send and receive e-mail) is quicker. If there is no packet data coverage, the device periodically tries to establish a packet data connection. If you select When needed, the device uses a 108

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
Tools
108
Security settings for
WEP
are as follows:
Wep key in use
—Select the WEP key number. You can
create up to four WEP keys. The same settings must be
entered on the wireless LAN access point device.
Authentication type
—Select
Open
or
Shared
for the
authentication type between your device and the wireless
LAN access point device.
WEP key settings
—Enter
WEP encryption
(length of the
key),
WEP key format
(
ASCII
or
Hexadecimal
), and
WEP
key
(the WEP key data in the selected format).
Security settings for
802.1x
and
WPA/WPA2
are as
follows:
WPA mode
—Select the means of authentication:
EAP
to
use an extensible authentication protocol (EAP) plug-in or
Pre-shared key
to use a password. Complete the
appropriate settings:
EAP plug-in settings
(only for
EAP
)—Enter the settings as
your service provider instructs.
Pre-shared key
(only for
Pre-shared key
)—Enter a
password. The same password must be entered on the
wireless LAN access point device.
TKIP encryption
—Select whether Temporal Key Integrity
Protocol (TKIP) is used.
Homepage
—Define a home page.
Select
Options
>
Advanced settings
and from the
following:
IPv4 settings
:
Phone IP address
(the IP address of your
device),
Subnet mask
(the subnet IP address),
Default
gateway
(the gateway), and
DNS address
—Enter the IP
addresses of the primary and secondary DNS server.
Contact your internet service provider for these addresses.
IPv6 settings
>
DNS address
—Select
Automatic
,
Well-known
, or
User defined
.
Ad-hoc channel
(only for
Ad-hoc
)—To enter a channel
number (1-11) manually, select
User defined
.
Proxy serv. address
—Enter the address for the proxy
server.
Proxy port number
—Enter the proxy port number.
Packet data
The packet data settings affect all access points using a
packet data connection.
Packet data conn.
—If you select
When available
and you
are in a network that supports packet data, the device
registers to the packet data network. Starting an active
packet data connection (for example, to send and receive
e-mail) is quicker. If there is no packet data coverage, the
device periodically tries to establish a packet data
connection. If you select
When needed
, the device uses a