Onkyo TX-NR809 Owner Manual - Page 80
About DTS signals, Can't select the Pure Audio listening mode
View all Onkyo TX-NR809 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 80 highlights
■ Only the front speakers produce sound When the Stereo or Mono listening mode is selected, - only the front speakers and subwoofer produce sound. In the Mono listening mode, only the front speakers 51 output sound if the "Output Speaker" setting is set to "Left / Right". Check the Speaker Configuration. 48 ■ Only the center speaker produces sound If you use the Dolby Pro Logic IIx Movie, Dolby Pro - Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker. In the Mono listening mode, only the center speaker 51 output sound if the "Output Speaker" setting is set to "Center". Make sure the speakers are configured correctly. 48 ■ The surround speakers produce no sound When the T-D (Theater-Dimensional), Stereo or - Mono listening mode is selected, the surround speakers produce no sound. Depending on the source and current listening mode, - not much sound may be produced by the surround speakers. Try selecting another listening mode. Make sure the speakers are configured correctly. 48 ■ The center speaker produces no sound When the Stereo or Mono listening mode is selected, - the center speaker produces no sound. In the Mono listening mode, only the front speakers 51 output sound if the "Output Speaker" setting is set to "Left / Right". Make sure the speakers are configured correctly. 48 ■ The front high, front wide and surround back speakers produce no sound Depending on the current listening mode, no sound 35 may be produced by the front high, front wide and surround back speakers. Select another listening mode. Depending on the sound source, the sound produced - by the front high, front wide and surround back speakers may be weak. Make sure the speakers are configured correctly. 48 While the "Powered Zone 2" setting is set to "Yes", 66 playback in the main room is reduced to 5.1channels and the front wide and surround back speakers produce no sound. ■ The subwoofer produces no sound When you play a source material that contains no - information in the LFE channel, the subwoofer produces no sound. Make sure the speakers are configured correctly. 48 ■ There's no sound with a certain signal format Check the digital audio output setting on the - connected device. On some game consoles, such as En those that support DVD, the default setting is off. 80 With some DVD-Video discs, you need to select an - audio output format from a menu. Depending on the input signal, some listening modes 35-39 cannot be selected. ■ Can't select the Pure Audio listening mode The Pure Audio listening mode cannot be selected - while Zone 2/3 is on. ■ Can't get 6.1/7.1 playback If no surround back speakers, front wide and front - high speakers are connected, or the Zone 2 speakers are being used, 6.1/7.1 playback is not possible. Depending on the number of connected speakers, it 35-39 is not always possible to select all of the listening modes. ■ The speaker volume cannot be set as required Check to see if a maximum volume has been set. If the volume level of each individual speaker has been adjusted to high positive values, then the maximum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey MultEQ® XT Room Correction and Speaker Setup has been performed. 59 31, 49 ■ Noise can be heard Using cable ties to bundle audio cables with power - cords, speaker cables, and the like may degrade the audio performance, so refrain from doing it. An audio cable may be picking up interference. Try - repositioning your cables. ■ The Late Night function doesn't work Make sure the source material is Dolby Digital, 64 Dolby Digital Plus, and Dolby TrueHD. ■ The analog multichannel input doesn't work Check the multichannel input connections. - Make sure that the multichannel input is selected. 57 Check the audio output settings on your source - component. ■ About DTS signals When DTS program material ends and the DTS - bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback. With some CD and LD players, you won't be able to - playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn't recognize it as a genuine DTS signal. In such cases, you may hear noise.