Onkyo TX-SR706 Owner Manual - Page 45

Speaker Settings

Get Onkyo TX-SR706 - AV Receiver PDF manuals and user guides
UPC - 751398008214
View all Onkyo TX-SR706 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

First Time Setup-Continued Speaker Settings 4 If you change these settings, you must run the automatic speaker setup again (see page 49). If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you've connected your front speakers to the FRONT L/R and SURR BACK L/R terminal posts for bi-amping, you must change the "Speakers Type" setting. For hookup information, see "Bi-amping the Front Speak- ers" on page 19. Notes: • When bi-amping is used, the AV receiver/AV ampli- fier is able to drive up to 5.1 speakers in the main room. 5 • Before you change these settings, turn down the vol- ume. 1 Press the [RECEIVER] button, followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. Use the Up and Down [R]/[X] buttons to select "Speakers Type", and then use the Left and Right [F]/[S] buttons to select: Normal: Select this if you've con- nected your front speakers normally. Bi-Amp:Select this if you've connected your front speakers for bi-amped operation. Notes: • Powered Zone2 cannot be used if "Speakers Type" is set to "Bi-Amp". • The analog multichannel input can- not be used if "Speakers Type" is set to "Bi-Amp". Use the Up and Down [R]/[X] buttons to select "Speaker Impedance", and then use the Left and Right [F]/[S] buttons to select: 4ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6ohms: Select if the impedances of all speakers are between 6 and 16 ohms. 2 Use the Up and Down [R]/[X] buttons to select "2. Speaker 6 Press the [SETUP] button. Setup", and then press [ENTER]. The setup menu closes. The "Speaker Setup" menu appears. 2. Speaker Setup 1. Speaker Settings 2. Speaker Configuration 3. Speaker Distance 4. Level Calibration 5. Equalizer Settings 6. THX Audio Setup Note: This procedure can also be performed on the AV receiver/AV amplifier by using its [SETUP] button, arrow buttons, and [ENTER] button. 3 Use the Up and Down [R]/[X] but- tons to select "1. Speaker Set- tings", and then press [ENTER]. The "Speaker Settings" menu appears. 2-1. Speaker Settings Speakers Type Speaker Impedance Normal 6ohms 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
45
First Time Setup
—Continued
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK L/R terminal posts for bi-amping,
you must change the “Speakers Type” setting. For
hookup information, see “Bi-amping the Front Speak-
ers” on page 19.
Notes:
•
When bi-amping is used, the AV receiver/AV ampli-
fier is able to drive up to 5.1 speakers in the main
room.
•
Before you change these settings, turn down the vol-
ume.
Note:
This procedure can also be performed on the AV
receiver/AV amplifier by using its [SETUP] button,
arrow buttons, and [ENTER] button.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q
]/[
w
] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
3
Use the Up and Down [
q
]/[
w
] but-
tons to select “1. Speaker Set-
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
If you change these settings, you must run the auto-
matic speaker setup again (see page 49).
2. Speaker Setup
1. Speaker Settings
2. Speaker Configuration
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
2–1. Speaker Settings
Speakers Type
Speaker Impedance
Normal
6ohms
4
Use the Up and Down [
q
]/[
w
] but-
tons to select “Speakers Type”,
and then use the Left and Right
[
e
]/[
r
] buttons to select:
Normal:
Select this if you’ve con-
nected your front speakers
normally.
Bi-Amp:
Select this if you’ve con-
nected your front speakers for
bi-amped operation.
Notes:
•
Powered Zone2 cannot be used if
“Speakers Type” is set to “Bi-Amp”.
•
The analog multichannel input can-
not be used if “Speakers Type” is set
to “Bi-Amp”.
5
Use the Up and Down [
q
]/[
w
] but-
tons to select “Speaker Imped-
ance”, and then use the Left and
Right [
e
]/[
r
] buttons to select:
4ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
6ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
6
Press the [SETUP] button.
The setup menu closes.