Onkyo TX-SR706 Owner Manual - Page 74

Use the Up and Down, then use the Left and Right

Get Onkyo TX-SR706 - AV Receiver PDF manuals and user guides
UPC - 751398008214
View all Onkyo TX-SR706 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Advanced Setup-Continued 5 Use the Up and Down [R]/[X] but- 8 tons to select "Front", and then use the Left and Right [F]/[S] buttons to select a crossover fre- quency. Note: If the "Subwoofer" setting in step 4 is set to "No", this setting is fixed at "Full Band". 6 Use the Up and Down [R]/[X] but- tons to select "Center", and then use the Left and Right [F]/[S] buttons to select a crossover fre- quency. If no center speaker is connected, select 9 "None". Note: If the "Front" setting in step 5 is set to anything other than "Full Band", "Full Band" cannot be selected here. 7 Use the Up and Down [R]/[X] but- tons to select "Surround", and then use the Left and Right [F]/ [S] buttons to select a crossover frequency. If no surround left and right speakers are connected, select "None". Note: If the "Front" setting in step 5 is set to anything other than "Full Band", "Full Band" cannot be selected here. Use the Up and Down [R]/[X] buttons to select "Surr Back", and then use the Left and Right [F]/ [S] buttons to select a crossover frequency. If no surround back speakers are connected, select "None". Notes: • If the "Surround" setting in step 7 is set to "None", this setting cannot be selected. • If the "Surround" setting in step 7 is set to anything other than "Full Band", "Full Band" cannot be selected here. • If the "Speakers Type" setting is set to "Bi-Amp" (page 45), or Powered Zone 2 is being used (page 98), this setting cannot be selected. Use the Up and Down [R]/[X] buttons to select "Surr Back Ch", and then use the Left and Right [F]/[S] buttons to select: 1ch: Select if one surround back speaker is connected. 2ch: Select if two (left and right) surround back speakers are connected. Note: If the "Surr Back" Setting in step 8 is set to "None", this setting cannot be selected. Continue with step 10 on the next page. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
74
Advanced Setup
—Continued
5
Use the Up and Down [
q
]/[
w
] but-
tons to select “Front”, and then
use the Left and Right [
e
]/[
r
]
buttons to select a crossover fre-
quency.
Note:
If the “Subwoofer” setting in step 4 is
set to
“No”
, this setting is fixed at “Full
Band”.
6
Use the Up and Down [
q
]/[
w
] but-
tons to select “Center”, and then
use the Left and Right [
e
]/[
r
]
buttons to select a crossover fre-
quency.
If no center speaker is connected, select
“None”.
Note:
If the
“Front”
setting in step 5 is set to
anything other than
“Full Band”
,
“Full
Band”
cannot be selected here.
7
Use the Up and Down [
q
]/[
w
] but-
tons to select “Surround”, and
then use the Left and Right [
e
]/
[
r
] buttons to select a crossover
frequency.
If no surround left and right speakers
are connected, select “None”.
Note:
If the
“Front”
setting in step 5 is set to
anything other than
“Full Band”
,
“Full
Band”
cannot be selected here.
8
Use the Up and Down [
q
]/[
w
] but-
tons to select “Surr Back”, and
then use the Left and Right [
e
]/
[
r
] buttons to select a crossover
frequency.
If no surround back speakers are con-
nected, select “None”.
Notes:
•
If the “Surround” setting in step 7 is
set to “None”, this setting cannot be
selected.
•
If the “Surround” setting in step 7 is
set to anything other than “Full
Band”, “Full Band” cannot be
selected here.
•
If the “Speakers Type” setting is set
to “Bi-Amp” (page 45), or Powered
Zone 2 is being used (page 98), this
setting cannot be selected.
9
Use the Up and Down [
q
]/[
w
] but-
tons to select “Surr Back Ch”,
and then use the Left and Right
[
e
]/[
r
] buttons to select:
1ch:
Select if one surround back
speaker is connected.
2ch:
Select if two (left and right)
surround back speakers are
connected.
Note:
If the
“
Surr Back
”
Setting in step 8 is
set to
“None”
, this setting cannot be
selected.
Continue with step 10 on the next page.