Onkyo TX-SR706 Owner Manual - Page 88

Picture Adjust, Picture Mode, Brightness, Contrast, Saturation, Edge Enhancement, Default - reset

Page 88 highlights

Advanced Setup-Continued Picture Adjust Using Picture Adjust, you can adjust the picture quality and reduce any noise appearing on the screen and set it to that adjustment. Use the Up and Down [R]/[X] buttons to select the settings, and use the Left and Right [F]/[S] buttons to set them. To view the TV picture while setting, press [ENTER]. To return to the previous screen, press the [RETURN] button. ■ Picture Mode AV receiver/AV amplifier comes with three Picture Modes (picture setting patterns): "Mode1" (default), "Mode2", and "Mode3". ■ Brightness With this setting you can adjust the picture brightness. Can be adjusted from -20 to +20 in steps of 1 (default is 0). "-20" is the darkest. "+20" is the brightest. ■ Contrast With this setting you can adjust Contrast. Can be adjusted from -20 to +20 in steps of 1 (default is 0). "-20" is the least. "+20" is the greatest. ■ Hue With this setting you can adjust the red/green balance. Can be adjusted from -20 to +20 in steps of 1 (default is 0). "-20" is the strongest green. "+20" is the strongest red. ■ Saturation With this setting you can adjust saturation. Can be adjusted from -20 to +20 in steps of 1 (default is 0). "-20" is the weakest color. "+20" is the strongest color. ■ Edge Enhancement With this setting you can adjust the sharpness of edges in the picture. Can be adjusted from 0 to +10 in steps of 1 (default is 0). "0" is the softest. "+10" is the sharpest. ■ Default You can reset the "Picture Adjust" to its default settings. Press the Right [S] button or [ENTER] to reset "Picture Adjust" settings. Note: For optimal video performance, THX recommends that the "Picture Adjust" be set to its default settings. 88 ■ Noise Reduction With this setting, you can reduce noise appearing on the screen. Off: Noise reduction off. Low: Low noise reduction (default). Mid: Medium noise reduction. High: High noise reduction. Note: The "Picture Adjust" (except "Default") can also be set using the [DISPLAY] button on the remote controller. 1. Press and hold the [DISPLAY] button until the set- ting item appears on the display. 2. Use the Up and Down [R]/[X] buttons to select an item, and use the Left and Right [F]/[S] buttons to change the setting.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120

88
Advanced Setup
—Continued
Picture Adjust
Using Picture Adjust, you can adjust the picture quality
and reduce any noise appearing on the screen and set it
to that adjustment.
Use the Up and Down [
q
]/[
w
] buttons to select the set-
tings, and use the Left and Right [
e
]/[
r
] buttons to set
them.
To view the TV picture while setting, press [ENTER].
To return to the previous screen, press the [RETURN]
button.
Picture Mode
AV receiver/AV amplifier comes with three Picture
Modes (picture setting patterns): “Mode1” (default),
“Mode2”, and “Mode3”.
Brightness
With this setting you can adjust the picture brightness.
Can be adjusted from –20 to +20 in steps of 1 (default is
0).
“–20” is the darkest.
“+20” is the brightest.
Contrast
With this setting you can adjust Contrast.
Can be adjusted from –20 to +20 in steps of 1 (default is
0).
“–20” is the least.
“+20” is the greatest.
Hue
With this setting you can adjust the red/green balance.
Can be adjusted from –20 to +20 in steps of 1 (default is
0).
“–20” is the strongest green.
“+20” is the strongest red.
Saturation
With this setting you can adjust saturation.
Can be adjusted from –20 to +20 in steps of 1 (default is
0).
“–20” is the weakest color.
“+20” is the strongest color.
Edge Enhancement
With this setting you can adjust the sharpness of edges in
the picture.
Can be adjusted from 0 to +10 in steps of 1 (default is 0).
“0” is the softest.
“+10” is the sharpest.
Default
You can reset the “Picture Adjust” to its default settings.
Press the Right [
r
] button or [ENTER] to reset “Picture
Adjust” settings.
Note:
For optimal video performance, THX recommends that
the “Picture Adjust” be set to its default settings.
Noise Reduction
With this setting, you can reduce noise appearing on the
screen.
Note:
The “Picture Adjust” (except “Default”) can also be set
using the [DISPLAY] button on the remote controller.
1.
Press and hold the [DISPLAY] button until the set-
ting item appears on the display.
2.
Use the Up and Down [
q
]/[
w
] buttons to select an
item, and use the Left and Right [
e
]/[
r
] buttons to
change the setting.
Off:
Noise reduction off.
Low:
Low noise reduction (default).
Mid:
Medium noise reduction.
High:
High noise reduction.