Optoma TH1060P User's Manual - Page 4

Precautions, Please follow all warnings, maintenance as recommended in this user's, guide. - lamp

Get Optoma TH1060P PDF manuals and user guides View all Optoma TH1060P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user's guide. ▀■ Warning- ▀■ Warning- ▀■ Warning- ▀■ Warning- ▀■ Warning- ▀■ Warning- ▀■ Warning- Noottee ▀■ Warning- When the lamp reaches the end of its life, the projector will not turn ▀■ Warning- back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under "Replacing the Lamp" section on page 42. Do not look into the projector's lens when the lamp is on. The bright light may hurt your eyes. To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. Please do not open or disassemble the projector as this may cause electric shock. When replacing the lamp, please allow the unit to cool down. Follow instructions as described on page 42. This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. Reset the "Lamp Reset" function from the on-screen display "System|Lamp Setting" menu after replacing the lamp module (refer to page 28). When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to cool down. Do not use lens cap when projector is in operation. When the lamp is approaching to the end of its life time, the message "Replacement suggested" will show on the screen. Please contact your local reseller or service center to change the lamp as soon as possible. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
²
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
When the lamp reaches
the end of its life, the
projector will not turn
back on until the lamp
module has been
replaced. To replace
the lamp, follow the
procedures listed under
"Replacing the Lamp"
section on page 42.
▀
■
Warning-
Do not look into the projector's lens when the
lamp is on.
The bright light may hurt your
eyes.
▀
■
Warning-
To reduce the risk of fire or electric shock, do
not expose this projector to rain or moisture.
▀
■
Warning-
Please do not open or disassemble the
projector as this may cause electric shock.
▀
■
Warning-
When replacing the lamp, please allow the
unit to cool down.
Follow instructions as
described on page 42.
▀
■
Warning-
This projector will detect the life of the lamp
itself.
Please be sure to change the lamp
when it shows warning messages.
▀
■
Warning-
Reset the "Lamp Reset" function from the
on-screen display "System|Lamp Setting"
menu after replacing the lamp module
(refer to page 28).
▀
■
Warning-
When switching the projector off, please
ensure the cooling cycle has been completed
before disconnecting power. Allow 90 seconds
for the projector to cool down.
▀
■
Warning-
Do not use lens cap when projector is in
operation.
▀
■
Warning-
When the lamp is approaching to the end of its
life time, the message "Replacement
suggested" will show on the screen.
Please contact your local reseller or service
center to change the lamp as soon as
possible.
N
ote
N
ote